- 您现在的位置：买卖IC网 > PDF目录80479 > MB90341APF (FUJITSU LTD) 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | MB90341APF |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | PLASTIC, QFP-100 |
| 文件页数： | 17/84页 |
| 文件大小： | 1130K |
| 代理商： | MB90341APF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
MB90340 Series
24
5.
Notes on during operation of PLL clock mode
If the PLL clock mode is selected, the microcontroller attempt to be working with the self-oscillating circuit even
when there is no external oscillator or external clock input is stopped. Performance of this operation, however,
cannot be guaranteed.
6.
Power supply pins (VCC/VSS)
If there are multiple VCC and VSS pins, from the point of view of device design, pins to be of the same potential
are connected the inside of the device to prevent such malfunctioning as latch up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the VCC and VSS pins to the power supply
and ground externally.
Connect VCC and VSS to the device from the current supply source at a low impedance.
As a measure against power supply noise, connect a capacitor of about 0.1
F as a bypass capacitor between
VCC and VSS in the vicinity of VCC and VSS pins of the device
7.
Pull-up/down resistors
The MB90340 Series does not support internal pull-up/down resistors (Port 0 to Port 3: built-in pull-up resistors).
Use external components where needed.
8.
Crystal Oscillator Circuit
Noises around X0 or X1 pins may be possible causes of abnormal operations. Make sure to provide bypass
capacitors via shortest distance from X0, X1 pins, crystal oscillator (or ceramic resonator) and ground lines, and
make sure, to the utmost effort, that lines of oscillation circuit not cross the lines of other circuits.
It is highly recommended to provide a printed circuit board art work surrounding X0 and X1 pins with a ground
area for stabilizing the operation.
9.
Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs
Make sure to turn on the A/D converter power supply (AVCC, AVRH, AVRL) and analog inputs (AN0 to AN23)
after turning-on the digital power supply (VCC) .
Turn-off the digital power after turning off the A/D converter supply and analog inputs. In this case, make sure
that the voltage not exceed AVRH or AVCC (turning on/off the analog and digital power supplies simultaneously
is acceptable) .
10. Connection of Unused Pins of A/D Converter if A/D Converter is used
Connect unused pins of A/D converter to AVCC
= VCC, AVSS = AVRH = AVRL = VSS.
Vcc
Vss
Vcc
Vss
Vcc
MB90340
Series
Vcc
Vss
Vcc
Vss
相关PDF资料 |
PDF描述 |
|---|---|
| MB90F349ASPF | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 |
| MC68HLC908QY1P | 8-BIT, FLASH, 2 MHz, MICROCONTROLLER, PDIP16 |
| MC68HC908AZ60MFU | 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| MC9328MXLVM20 | 32-BIT, 200 MHz, RISC PROCESSOR, PBGA256 |
| MCF5274LVM166 | 32-BIT, 166 MHz, RISC PROCESSOR, PBGA196 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90341CE | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Microcontroller |
| MB90341CEPF | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller CMOS |
| MB90341CEPFV | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller CMOS |
| MB90341CES | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Microcontroller |
| MB90341CESPF | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller CMOS |
发布紧急采购，3分钟左右您将得到回复。