- 您现在的位置：买卖IC网 > PDF目录45191 > MB90362TESPMT MICROCONTROLLER, PQFP48 PDF资料下载
参数资料
| 型号： | MB90362TESPMT |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | MICROCONTROLLER, PQFP48 |
| 封装： | PLASTIC, LQFP-48 |
| 文件页数： | 32/60页 |
| 文件大小： | 711K |
| 代理商： | MB90362TESPMT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
MB90360E Series
38
(Continued)
*1 : This parameter is based on VSS
= AVSS = 0 V.
*2 : Set AVCC and VCC to the same voltage. Make sure that AVCC does not exceed VCC and that the voltage at the
analog inputs does not exceed AVCC when the power is switched on.
*3 : VI and VO should not exceed VCC
+ 0.3 V. VI should not exceed the specified ratings. However, if the maximun
current to/from an input is limited by some means with external components, the ICLAMP rating supersedes the
VI rating.
*4 : Applicable to pins : P24 to P27, P40 to P44, P50 to P57, P60 to P67, P80, P82 to P87
*5 : Applicable to pins : P20 to P23
*6 : Applicable to pins : P20 to P27, P40 to P44, P50 to P57, P60 to P67, P80, P82 to P87
Use within recommended operating conditions.
Use at DC voltage (current) .
The +B signal should always be applied a connecting limit resistance between the +B signal and the
microcontroller.
The value of the limiting resistance should be set so that when the +B signal is applied the input current to
the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this may affect
other devices.
Note that if a +B signal is inputted when the microcontroller power supply is off (not fixed at 0 V) , the power
supply is provided from the pins, so that incomplete operation may result.
Note that if the +B input is applied during power-on, the power supply is provided from the pins and the
resulting power supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the +B input pin open.
Recommended circuit sample :
*7 : If used exceeding TA
= +105 °C, please consult with us due to the restricted reliability.
It is ensured to write/erase data to the Flash memory between TA
= 40 °C and +105 °C.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
P-ch
N-ch
VCC
R
Input/output equivalent circuits
+B input (0 V to 16 V)
Limiting
resistance
Protective diode
相关PDF资料 |
PDF描述 |
|---|---|
| MB90367TEPMT | MICROCONTROLLER, PQFP48 |
| MB90F367EPMT | MICROCONTROLLER, PQFP48 |
| MB90F367TESPMT | MICROCONTROLLER, PQFP48 |
| MB90F367SPMT | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48 |
| MB90F367TSPMT | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90362TPMT | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90362TS | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90362TSPMT | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90367 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90367E | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
发布紧急采购，3分钟左右您将得到回复。