- 您现在的位置：买卖IC网 > PDF目录98010 > MB90497GPFM 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | MB90497GPFM |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64 |
| 封装： | PLASTIC, LQFP-64 |
| 文件页数： | 7/90页 |
| 文件大小： | 849K |
| 代理商： | MB90497GPFM |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页
MB90495G Series
15
A/D Converter Power-up and Analog Input Initiation Sequence
Make sure to power up the A/D converter and analog input (pins AN0 to AN7) after turning on digital power
(VCC) .
Turn off digital power after turning off the A/D converter power supply and analog inputs. In this case, make
sure that the voltage of AVR does not exceed AVCC (it is permissible to turn off analog and digital power
simultaneously) .
Connecting Unused A/D Converter Pins
If you are not using the A/D converter, set unused pins to AVCC
= AVR = VCC, AVSS = VSS.
Notes for Powering Up
Ensure that the voltage step-up time (between 0.2 V and 2.7 V) at power-up is no less than 50
s, in order to
prevent malfunction in the built-in step-down circuit. 12
Initialization
The device contains built-in registers which are only initialized by a power-on reset. Cycle the power supply to
initialize these registers.
Stabilizing the Power Supply
Make sure that the VCC power supply voltage is stable. Even at the rated operating VCC power supply voltage,
large, sudden changes in the voltage could cause malfunctions. As a standard for stable power supply, keep
VCC ripples (peak-to-peak value) at commercial power frequencies (50 Hz to 60 Hz) to no more than 10
% of the
power supply voltage, and momentary surges caused by switching the power supply and other events to more
than 0.1 V/ms.
If Output from Ports 0/1 Becomes Undefined
After power is turned on, if the RST pin is set to “H” during step-down circuit stabilization standby (during power-
on reset) , ports 0 and 1 output will be undefined. If the RST pin is set to “L”, ports 0 and 1 will go into a high
impedance state. Take careful note of the timing of events outlined in figures 1 and 2.
相关PDF资料 |
PDF描述 |
|---|---|
| MB90F498GPMC | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64 |
| MB90497GPMC | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64 |
| MB90F574/APFF | 16-BIT, FLASH, MICROCONTROLLER, PQFP120 |
| MB90F997MBSPMC | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 |
| MB90F997JBSPMC | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90497GPMC | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90520A | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90520B | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90522 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90522A | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
发布紧急采购，3分钟左右您将得到回复。