- 您现在的位置：买卖IC网 > PDF目录80529 > MB90553BPF 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | MB90553BPF |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | PLASTIC, QFP-100 |
| 文件页数： | 7/61页 |
| 文件大小： | 687K |
| 代理商： | MB90553BPF |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页
MB90550A/550B Series
15
s HANDLING DEVICES
1.
Preventing Latchup
CMOS ICs may cause latchup in the following situations:
When a voltage higher than Vcc or lower than Vss is applied to input or output pins.
When a voltage exceeding the rating is applied between Vcc and Vss.
When AVcc power is supplied prior to the Vcc voltage.
If latchup occurs, the power supply current increases rapidly, sometimes resulting in thermal breakdown of the
device. Use meticulous care not to let it occur.
For the same reason, also be careful not to let the analog power-supply voltage exceed the digital power-supply
voltage.
2.
Handling unused input pins
Leaving unused input pins open may cause a malfunction or latch-up which leads to fatal damage to the device.
Therefore they must be pulled up or pulled down through at least 2 k
resistance. Also, unused input/output
pins should be left open in output state or handled in the same way as unused input pins.
3.
Notes on Using External Clock
In using the external clock, drive X0 pin only and leave X1 pin unconnected.
4.
Power Supply Pins (VCC/VSS)
In products with multiple VCC or VSS pins, the pins of a same potential are internally connected in the device to
avoid abnormal operations including latch-up. However, the pins should be connected to external power and
ground lines to lower the electro-magnetic emission level and abnormal operation of strobe signals caused by
the rise in the ground level, and to conform to the total current rating.
Make sure to connect VCC and VSS pins via lowest impedance to power lines.
It is recommended that a bypass capacitor of around 0.1
F be placed between the VCC and VSS pins near the
device.
Using external clock
MB90550A/550B series
X0
X1
Open
VCC
VSS
Using power supply pins
MB90550A/550B
series
相关PDF资料 |
PDF描述 |
|---|---|
| M306NAMCT-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB89P475P-SH-102 | 8-BIT, 12.5 MHz, MICROCONTROLLER, PDIP48 |
| MC68HC908QY4CDT | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16 |
| MC6805U2L | 8-BIT, MROM, MICROCONTROLLER, CDIP40 |
| MC68HC908QT1CFQ | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, DSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90553BPFV | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90553BPMC | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB90560 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
| MB90560_08 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
| MB90561 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。