参数资料
型号: MB90F342CAPF
厂商: FUJITSU LTD
元件分类: 微控制器/微处理器
英文描述: 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
封装: PLASTIC, QFP-100
文件页数: 18/84页
文件大小: 1130K
代理商: MB90F342CAPF
MB90340 Series
25
11. Notes on Energization
To prevent the internal regulator circuit from malfunctioning, set the voltage rise time during energization at 50
or more
s (0.2 V to 2.7 V)
12. Stabilization of power supply voltage
A sudden change in the supply voltage may cause the device to malfunction even within the specified VCC supply
voltage operating range. Therefore, the VCC supply voltage should be stabilized.
For reference, the supply voltage should be controlled so that VCC ripple variations (peak-to-peak value) at
commercial frequencies (50 Hz to 60 Hz) fall below 10
% of the standard VCC supply voltage and the coefficient
of fluctuation does not exceed 0.1 V/ms at instantaneous power switching.
13. Initialization
In the device, there are internal registers which are initialized only by a power-on reset. To initialize these registers,
turn on the power again.
14. Port 0 to port 3 output during Power-on (External-bus mode)
As shown below, when power is turned on in External-Bus mode, in spite of reset inpu, there is a possibility that
output signal of Port 0 to Port 3 might be unstable.
15. Notes on using CAN Function
To use CAN function, please set ’1’ to DIRECT bit of CAN Direct Mode Register (CDMR).
If DIRECT bit is set to ’0’ (initial value), wait states will be performed when accessing CAN registers.
Please refer to Hardware Manual of MB90340 series for detail of CAN Direct Mode Register.
16. Flash security Function (except for MB90F346A)
The security bit is located in the area of the flash memory.
If protection code 01H is written in the security bit, the flash memory is in the protected state by security.
Therefore please do not write 01H in this address if you do not use the security function.
Please refer to following table for the address of the security bit.
Flash memory size
Address for security bit
MB90F347
MMB90F347A
Embedded 1 Mbit Flash Memory
FE0001H
MB90F342A
MB90F349A
Embedded 2 Mbit Flash Memory
FC0001H
MB90F343A
Embedded 3 Mbit Flash Memory
F90001H
MB90F345A
Embedded 4 Mbit Flash Memory
F80001H
Port0 to 3 outputs
might be unstable
Port0 to 3 outputs = Hi-Z
Port0 ~ Port3
VCC
1/2VCC
相关PDF资料
PDF描述
MB90F347CASPFR-GSE1 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
MB90341ASPFV 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100
MB90F345CASPF 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
MB90F349APFV 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
MB90F349CASPFV 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
相关代理商/技术参数
参数描述
MB90F342CAPFR-GSE1 制造商:FUJITSU 功能描述:
MB90F342CASPFR-GS 功能描述:IC MCU FLASH 256K ROM 100-QFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:F²MC MB90340 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA,UART/USART 外围设备:欠压检测/复位,LED,POR,PWM,WDT 输入/输出数:16 程序存储器容量:4KB(4K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC(0.295",7.50mm 宽) 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND
MB90F342CASPFR-GSE1 制造商:FUJITSU 功能描述:
MB90F342CASPFR-GS-N2E1 功能描述:IC MCU 16BIT 256KB FLASH 100QFP 制造商:cypress semiconductor corp 系列:F2MC-16LX MB90340 包装:托盘 零件状态:在售 核心处理器:F2MC-16LX 核心尺寸:16-位 速度:24MHz 连接性:CAN,EBI/EMI,I2C,LIN,SCI,UART/USART 外设:DMA,POR,WDT I/O 数:82 程序存储容量:256KB(256K x 8) 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:16K x 8 电压 - 电源(Vcc/Vdd):3 V ~ 5.5 V 数据转换器:A/D 24x8/10b 振荡器类型:外部 工作温度:-40°C ~ 105°C(TA) 封装/外壳:100-BQFP 供应商器件封装:100-PQFP(20x14) 标准包装:66
MB90F342CASPMC-GSE1 制造商:FUJITSU 功能描述: