- 您现在的位置：买卖IC网 > PDF目录80580 > MB90F345CEPF MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | MB90F345CEPF |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 20 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件页数： | 15/84页 |
| 文件大小： | 1142K |
| 代理商： | MB90F345CEPF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
MB90340E Series
22
■ HANDLING DEVICES
1.
Preventing latch-up
CMOS IC may suffer latch-up under the following conditions:
A voltage higher than VCC or lower than VSS is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC and VSS pins.
The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, also be careful not to let the analog power-supply voltage (AVCC, AVRH) exceed the digital
power-supply voltage.
2.
Handling unused pins
Leaving unused input terminals open may lead to permanent damage due to malfunction and latch-up; pull up
or pull down the terminals through the resistors of 2 k
Ω or more.
3.
Power supply pins (VCC/VSS)
If there are multiple VCC and VSS pins, from the point of view of device design, pins to be of the same potential
are connected inside of the device to prevent malfunction such as latch-up.
To reduce unnecessary radiation, prevent malfunctioning of the strobe signal due to the rise of ground level,
and observe the standard for total output current, be sure to connect the VCC and VSS pins to the power supply
and ground externally.
Connect VCC and VSS pins to the device from the current supply source at a possibly low impedance.
As a measure against power supply noise, it is recommended to connect a capacitor of about 0.1
μF as a
bypass capacitor between VCC and VSS pins in the vicinity of VCC and VSS pins of the device.
4.
Mode Pins (MD0 to MD2)
Connect the mode pins directly to VCC or VSS pins. To prevent the device unintentionally entering test mode due
to noise, lay out the printed circuit board so as to minimize the distance from the mode pins to VCC or VSS pins
and to provide a low-impedance connection.
Vcc
Vss
Vcc
Vss
Vcc
MB90340E
Series
Vcc
Vss
Vcc
Vss
相关PDF资料 |
PDF描述 |
|---|---|
| M30102F3TFP | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP48 |
| M37481M8-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP44 |
| M37481M8T-XXXSP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP42 |
| MB96F356ASAPMC-GE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
| MB96F356RWAPMC1-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90F345CESPMC-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F347ASPMCR-GS-SPE2 | 制造商:FUJITSU 功能描述: |
| MB90F347CAPFR-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F347CAPFR-GS-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F347CASPF-GSE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU CAN 5V SMD QFP100 |
发布紧急采购，3分钟左右您将得到回复。