- 您现在的位置：买卖IC网 > PDF目录69020 > MB90F387SPMT 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP48 PDF资料下载
参数资料
| 型号： | MB90F387SPMT |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP48 |
| 封装： | PLASTIC, LQFP-48 |
| 文件页数： | 9/64页 |
| 文件大小： | 1777K |
| 代理商： | MB90F387SPMT |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
MB91260B Series
DS07-16507-3E
17
■ HANDLING DEVICES
Preventing Latch-up
Latch-up may occur in a CMOS IC if a voltage greater than VCC or less than VSS is applied to an input or output
pin or if an above-rating voltage is applied between VCC and VSS.
A latch-up, if it occurs, significantly increases the power supply current and may cause thermal destruction of
an element. When you use a CMOS IC, be very careful not to exceed the absolute maximum rating.
Treatment of Unused Pins
Do not leave an unused input pin open, since it may cause a malfunction. Handle by, for example, using a pull-
up or pull-down resistor.
About Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
F between VCC and VSS near
this device.
About Crystal Oscillator Circuit
Noise near the X0, X1, X0A and X1A pins may cause the device to malfunction. Design the printed circuit board
so that X0, X1, X0A and X1A the crystal oscillator (or ceramic oscillator) , and the bypass capacitor to ground
are located as close to the device as possible.
It is strongly recommended to design the PC board artwork with the X0, X1, X0A and X1A pins surrounded by
ground plane because stable operation can be expected with such a layout.
Please ask the crystal maker to evaluate the oscillational characteristics of the crystal and this device.
About Mode Pins (MD0 to MD2)
These pins should be connected directly to VCC or VSS.
To prevent the device erroneously switching to test mode due to noise, design the printed circuit board such that
the distance between the mode pins and VCC or VSS is as short as possible and the connection impedance is low.
Operation at Start-up
Be sure to execute setting initialized reset (INIT) with INIT pin immediately after start-up.
Also, in order to provide the oscillation stabilization wait time for the oscillation circuit immediately after start-up,
hold the “L” level input to the INIT pin for the required stabilization wait time. (For INIT via the INIT pin, the
oscillation stabilization wait time setting is initialized to the minimum value) .
About Oscillation Input at Power On
When turning the power on, maintain clock input until the device is released from the oscillation stabilization
wait state.
相关PDF资料 |
PDF描述 |
|---|---|
| MB90523BPFV | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP120 |
| MB90F523BPMC1 | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP120 |
| MB90549PF | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90F591PF | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| MB90574/BPFV | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP120 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90F387SPMT-GSE1 | 功能描述:IC MCU FLASH 64K ROM 48LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:F²MC MB90385 产品培训模块:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 标准包装:90 系列:AVR® XMEGA 核心处理器:AVR 芯体尺寸:8/16-位 速度:32MHz 连通性:I²C，IrDA，SPI，UART/USART 外围设备:欠压检测/复位，DMA，POR，PWM，WDT 输入/输出数:50 程序存储器容量:192KB（96K x 16） 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 电压 - 电源 (Vcc/Vdd):1.6 V ~ 3.6 V 数据转换器:A/D 16x12b; D/A 2x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:64-TQFP 包装:托盘 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| MB90F394HPMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F395HAPMCR-GS-SPE | 制造商:FUJITSU 功能描述:16-BIT, FLASH, 24 MHZ, MICROCONTROLLER, PQFP120 |
| MB90F428GAPMC-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F428GCPFR-GSE1 | 制造商:FUJITSU 功能描述: |
发布紧急采购，3分钟左右您将得到回复。