- 您现在的位置：买卖IC网 > PDF目录80392 > MB90F543PF 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | MB90F543PF |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | PLASTIC, QFP-100 |
| 文件页数： | 9/67页 |
| 文件大小： | 746K |
| 代理商： | MB90F543PF |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
MB90540/540G/545/545G Series
17
s
s HANDLING DEVICES
(1) Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions :
A voltage higher than VCC or lower than VSS is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC and VSS.
The AVcc power supply is applied before the VCC voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, care must also be taken in not allowing the analog power-supply voltage (AVCC, AVRH) to
exceed the digital power-supply voltage.
(2) Handling unused pins
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the
device. Therefor they must be pulled up or pulled down through resistors. In this case those resistors should be
more than 2 k
.
Unused bi-directional pins should be set to the output state and can be left open, or the input state with the
above described connection.
(3) Using external clock
To use external clock, drive X0 pin only and leave X1 pin unconnected.
Below is a diagram of how to use external clock.
(4) Use of the sub-clock
Use one clock system parts when the sub-clock is not used. In that case, pull-down the pin X0A and leave the
pin X1A open. When using two clock system parts, a 32 kHz oscillator has to be connected to the X0A and X1A
pins.
(5) Power supply pins (VCC/VSS)
In products with multiple VCC or VSS pins, the pins of a same potential are internally connected in the device to
avoid abnormal operations including latch-up. However you must connect the pins to an external power and a
ground line to lower the electro-magnetic emission level to prevent abnormal operation of strobe signals caused
by the rise in the ground level, and to conform to the total current rating.
Make sure to connect VCC and VSS pins via the lowest impedance to power lines.
It is recommended to provide a bypass capacitor of around 0.1
F between VCC and VSS pins near the device.
X0
X1
MB90540/545 Series
Open
VCC
VSS
MB90540/545
Series
相关PDF资料 |
PDF描述 |
|---|---|
| MPC603RPX200TC | 32-BIT, 200 MHz, RISC PROCESSOR, PBGA255 |
| MPC603RRX100RC | 32-BIT, 100 MHz, RISC PROCESSOR, CBGA255 |
| MPC755BPX400TD | 32-BIT, 400 MHz, RISC PROCESSOR, PBGA360 |
| M38749EFFS | 8-BIT, UVPROM, 6.4 MHz, MICROCONTROLLER, CQCC80 |
| MC68HC705JP7CS | 8-BIT, UVPROM, 2.1 MHz, MICROCONTROLLER, CDIP28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90F543PFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F546GPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F546GSPF-GE1 | 功能描述:IC MCU 16BIT 制造商:cypress semiconductor corp 系列:F2MC-16LX MB90545G 包装:托盘 零件状态:在售 核心处理器:F2MC-16LX 核心尺寸:16-位 速度:16MHz 连接性:CAN，EBI/EMI，SCI，串行输入/输出，UART/USART 外设:POR，WDT I/O 数:81 程序存储容量:256KB（256K x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:8K x 8 电压 - 电源（Vcc/Vdd）:4.5 V ~ 5.5 V 数据转换器:A/D 8x8/10b 振荡器类型:外部 工作温度:-40°C ~ 105°C（TA） 封装/外壳:100-BQFP 供应商器件封装:100-PQFP（20x14） 标准包装:66 |
| MB90F546GSPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F546GSPMC-GE1 | 制造商:FUJITSU 功能描述: |
发布紧急采购，3分钟左右您将得到回复。