- 您现在的位置：买卖IC网 > PDF目录80512 > MB90F584CPF (FUJITSU LTD) 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | MB90F584CPF |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 20 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件页数： | 24/112页 |
| 文件大小： | 2251K |
| 代理商： | MB90F584CPF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页
MB90580C Series
DS07-13710-7E
19
■ HANDLING DEVICES
1.
Preventing Latch-up
CMOS ICs may cause Latch-up in the following situations:
When a voltage higher than Vcc or lower than Vss is applied to input or output pins.
When a voltage exceeding the rating is applied between Vcc and Vss.
When AVcc power is supplied prior to the Vcc voltage.
If Latch-up occurs, the power supply current increases rapidly, sometimes resulting in thermal breakdown of the
device. Use meticulous care not to let it occur.
For the same reason, also be careful not to let the analog power-supply voltage exceed the digital power-supply
voltage.
2.
Handling unused input pins
Unused input pins left open may cause abnormal operation, or latch-up leading to permanent damage. Unused
input pins should be pulled up or pulled down through at least 2 k
Ω resistance.
Unused input/output pins may be left open in output state, but if such pins are in input state they should be
handled in the same way as input pins.
3.
Treatment of the TX and RX pins with the IEBusTM unused
When the IEBus is not used, connect a pull-down resistor to the TX pin and a pull-down/pull-up resistor to the
RX pin.
4.
Use of the external clock
When the device uses an external clock, drive only the X0 pin while leaving the X1 pin open (See the illustration
below).
5.
Power Supply Pins (VCC/VSS)
In products with multiple VCC or VSS pins, the pins of a same potential are internally connected in the device to
avoid abnormal operations including latch-up. However, connect the pins external power and ground lines to
lower the electro-magnetic emission level to prevent abnormal operation of strobe signals caused by the rise in
the ground level, and to conform to the total current rating.
Make sure to connect VCC and VSS pins via lowest impedance to power lines.
X0
X1
MB90580C series
Open
相关PDF资料 |
PDF描述 |
|---|---|
| M3062BFCTGP | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP80 |
| M38037M6-XXXFP | 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| M38039FFHP | 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| M38513E4SP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP42 |
| M30828MH-XXXGP | 32-BIT, MROM, 30 MHz, MICROCONTROLLER, PQFP144 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90F591GPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F594APFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F594GPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F598GPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F598GPFR-GSE1 | 功能描述:IC MCU 16BIT 制造商:cypress semiconductor corp 系列:F2MC-16LX MB90595G 包装:托盘 零件状态:在售 核心处理器:F2MC-16LX 核心尺寸:16-位 速度:16MHz 连接性:CAN，EBI/EMI，SCI，串行输入/输出，UART/USART 外设:POR，PWM，WDT I/O 数:78 程序存储容量:128KB（128K x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:4K x 8 电压 - 电源（Vcc/Vdd）:3 V ~ 5.5 V 数据转换器:A/D 8x8/10b 振荡器类型:外部 工作温度:-40°C ~ 85°C（TA） 封装/外壳:100-BQFP 供应商器件封装:100-PQFP（20x14） 标准包装:66 |
发布紧急采购，3分钟左右您将得到回复。