- 您现在的位置：买卖IC网 > PDF目录80361 > MB90F883BSPMC (FUJITSU LTD) 16-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | MB90F883BSPMC |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 14 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件页数： | 15/80页 |
| 文件大小： | 2171K |
| 代理商： | MB90F883BSPMC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
MB90880 Series
22
DS07-13743-5E
■ HANDLING DEVICES
1.
Maximum rated voltages for the prevention of latch-up
Be cautious not to exceed the absolute maximum rating.
CMOS ICs may cause latch-up, when a voltage higher than VCC or lower than VSS is applied to input or output
pins other than medium-to-high resistant pins, or when a voltage exceeding the rating is applied between VCC
and VSS pins.
If latch-up occurs, the power supply current increases rapidly, sometimes resulting in thermal breakdown of the
device. Take the utmost care not to let it occur.
Likewise, care must be taken not to allow the analog power supply (AVCC, AVRH) and analog input to exceed
the digital power supply (VCC) when turning on or off any analog system.
2.
Handling unused pins
Leaving unused input pins open may cause a malfunction or latch-up which leads to fatal damage to the device.
Therefore, they must be pulled up or down through at least 2 k
Ω resistance. Also, any unused I/O pin should be
left open in the output state, or set to the input state and handled in the same way as an unused input pin.
3.
Notes on using external clock
Even when an external clock is being used, oscillation stabilization wait time is required for a power-on reset or
release from sub clock mode or stop mode.
The following diagram shows an example of using an external clock.
4.
Handling power supply pins (VCC/VSS)
When multiple VCC and VSS pins supply pins are used, all the power supply pins must be connected to external
power and ground lines due to the device design, to reduce latch-up and unwanted radiation, prevent abnormal
operation of strobe signals caused by the rise in the ground level and to conform to the total output current rating.
Make sure to connect the VCC and VSS pins of this device via lowest impedance to power lines. It is recommended
that a bypass capacitor of around 0.1
μF be placed between the VCC and VSS pins near the device.
5.
Crystal oscillator circuit
Noises around X0/X1 or X0A/X1A pins may cause abnormal operations. It is strongly recommended to provide
bypass capacitors via shortest distance from X0/X1, X0A/X1A pins, crystal oscillator (or ceramic oscillator) and
ground lines and also not to allow the lines of the oscillation circuit to cross the lines of other circuits. This will
ensure stable operations of the printed circuit boards. Please ask each crystal maker to evaluate the oscillational
characteristics of the crystal and this device.
6.
Notes on PLL clock mode operation
If an oscillator comes off or clock input stops during PLL clock mode operation, this microcontroller may continue
its operation using a free-running frequency from a self-excited oscillation circuit within PLL. This is not a
guaranteed operation.
X0(X0A)
X1(X1A)
Open
相关PDF资料 |
PDF描述 |
|---|---|
| MB91F465DAPVSR-GSE2 | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP208 |
| M30280F8WG-U5 | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PBGA85 |
| M30620SPFP | 16-BIT, 24 MHz, MICROCONTROLLER, PQFP100 |
| M30626FHPFP-D9 | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 |
| M30627FHPGP-D9 | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP128 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90F897PMCR-G-TE1 | 制造商:FUJITSU 功能描述: |
| MB90F897PMT-GSE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU CAN 5V SMD LQFP48 |
| MB90F897SPMCR-GSE1 | 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 16BIT 16LX 64K FLASH 48LQFP 制造商:FUJITSU 功能描述:MCU, 16BIT, 16LX, 64K FLASH, 48LQFP 制造商:FUJITSU 功能描述:IC, 16BIT MCU, F2MC-16LX, 16MHZ, LQFP-48, Controller Family/Series:F2MC-16LX, Core Size:16bit, No. of I/O's:36, Supply Voltage Min:3.5V, Supply Voltage Max:5.5V, Digital IC Case Style:LQFP, No. of Pins:48, Program Memory Size:64KB , RoHS Compliant: Yes 制造商:FUJITSU 功能描述:MCU, 16BIT, 16LX, 64K FLASH, 48LQFP, Controller Family/Series:F2MC-16LX, Core Si |
| MB90F947APFR-GS-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F962SPMCR-GE1 | 制造商:FUJITSU 功能描述:IC MCU 16BIT 16LX 48LQFP |
发布紧急采购，3分钟左右您将得到回复。