- 您现在的位置：买卖IC网 > PDF目录80528 > MB90F897PMT MICROCONTROLLER, PQFP48 PDF资料下载
参数资料
| 型号： | MB90F897PMT |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | MICROCONTROLLER, PQFP48 |
| 封装： | 7 X 7 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-48 |
| 文件页数： | 54/84页 |
| 文件大小： | 1773K |
| 代理商： | MB90F897PMT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
MB90895 Series
58
DS07-13731-4E
(Continued)
*6 : An average current value of all pins within 100 ms is specified as an average total output current. (Average
value is found by multiplying operating current by operating rate.)
*7 :
Applicable to pins: P10 to P17, P20 to P27, P30 to P33, P35, P36, P37, P40 to P44, P50 to P57
Note: P35 and P36 are MB90F897S only.
Use within recommended operating conditions.
Use at DC voltage (current) .
The +B signal should always be applied a limiting resistance placed between the +B signal and the
microcontroller.
The value of the limiting resistance should be set so that when the +B signal is applied the input current to the
microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input potential
may pass through the protective diode and increase the potential at the VCC pin, and this may affect other
devices.
Note that if a +B signal is input when the microcontroller power supply is off (not fixed at 0 V) , the power supply is
provided from the pins, so that incomplete operation may result.
Note that if the +B input is applied during power-on, the power supply is provided from the pins and the
resulting supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the +B input pin open.
Note that analog system input/output pins other than the A/D input pins (LCD drive pins, comparator input
pins, etc.) cannot accept
+B signal input.
Sample recommended circuits:
*8 : Users considering application exceeding TA = +105
°C are advised to contact their FUJITSU MICROELEC-
TRONICS representatives beforehand for reliability limitations.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
P-ch
N-ch
VCC
R
Input/Output Equivalent circuits
+B input (0 V to 16 V)
Limiting
resistance
Protective diode
相关PDF资料 |
PDF描述 |
|---|---|
| MCF52258VN80 | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, BGA144 |
| MB91F639ABGL | 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PBGA144 |
| MB96F379YWAPMC-GSE2 | 16-BIT, FLASH, 80 MHz, MICROCONTROLLER, PQFP144 |
| MB96F353RSAPMC-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP64 |
| MPC5606SVLQ6 | 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP144 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90F897PMT-GSE1 | 制造商:FUJITSU 功能描述:IC 16BIT MCU CAN 5V SMD LQFP48 |
| MB90F897SPMCR-GSE1 | 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 16BIT 16LX 64K FLASH 48LQFP 制造商:FUJITSU 功能描述:MCU, 16BIT, 16LX, 64K FLASH, 48LQFP 制造商:FUJITSU 功能描述:IC, 16BIT MCU, F2MC-16LX, 16MHZ, LQFP-48, Controller Family/Series:F2MC-16LX, Core Size:16bit, No. of I/O's:36, Supply Voltage Min:3.5V, Supply Voltage Max:5.5V, Digital IC Case Style:LQFP, No. of Pins:48, Program Memory Size:64KB , RoHS Compliant: Yes 制造商:FUJITSU 功能描述:MCU, 16BIT, 16LX, 64K FLASH, 48LQFP, Controller Family/Series:F2MC-16LX, Core Si |
| MB90F947APFR-GS-SPE1 | 制造商:FUJITSU 功能描述: |
| MB90F962SPMCR-GE1 | 制造商:FUJITSU 功能描述:IC MCU 16BIT 16LX 48LQFP |
| MB90F962SPMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
发布紧急采购，3分钟左右您将得到回复。