- 您现在的位置：买卖IC网 > PDF目录45193 > MB91F264BPF-GE1 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | MB91F264BPF-GE1 |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, FLASH, 33 MHz, RISC MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 20 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, LEAD FREE, PLASTIC, QFP-100 |
| 文件页数： | 11/64页 |
| 文件大小： | 1403K |
| 代理商： | MB91F264BPF-GE1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
MB91260B Series
DS07-16507-3E
19
Clock Control Block
Input the “L” signal to the INIT pin to assure the clock oscillation stabilization wait time.
Switch Shared Port Function
To switch between the use as a port and the use as a dedicated pin, use the port function register (PFR) .
Low Power Consumption Mode
To enter the standby mode, use the synchronous standby mode (set with the SYNCS bit as bit 8 in the TBCR :
timebase counter control register) and be sure to use the following sequence
In addition, please set I flag, ILM, and ICR to diverge to the interruption handler that is the return factor after
the standby returns.
Please do not do the following when the monitor debugger is used.
Break point setting for above instruction lines
Step execution for above instruction lines
Notes on the PS register
As the PS register is processed by some instructions in advance, exception handling below may cause the
interrupt handling routine to break when the debugger is used or the display contents of flags in the PS register
to be updated.
As the microcontroller is designed to carry out reprocessing correctly upon returning from such an EIT event, it
performs operations before and after the EIT as specified in either case.
The following operations may be performed when the instruction immediately followed by a DIV0U/DIV0S
instruction is (a) acceptance of a user interrupt, (b) single-stepped, or (c) breaks in response to a data event
or emulator menu :
1) The D0 and D1 flags are updated in advance.
2) An EIT handling routine (user interrupt or emulator) is executed.
3) Upon returning from the EIT, the DIV0U/DIV0S instruction is executed, and the D0 and D1 flags are updated
to the same values as in 1).
The following operations are performed when the ORCCR/STILM/MOVRi and PS instructions are executed
to allow the interrupt.
(LDI
#value_of_standby, R0)
: Value_of standby is write data to STCR.
(LDI
#_STCR, R12)
: _STCR is address (481H) of STCR.
STB
R0, @R12
: Writing to standby control register (STCR)
LDUB
@R12, R0
: STCR read for synchronous standby
LDUB
@R12, R0
: Dummy re-read of STCR
NOP
: NOP
× 5 for arrangement of timing
NOP
相关PDF资料 |
PDF描述 |
|---|---|
| MB91F264BPMC-GE1 | RISC MICROCONTROLLER, PQFP100 |
| MB91263BPMC-G-XXXE1 | RISC MICROCONTROLLER, PQFP100 |
| MB91263BPF-G-XXXE1 | 32-BIT, MROM, 33 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91637APMC | 32-BIT, MROM, 40 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB91637ABGL | 32-BIT, MROM, 40 MHz, RISC MICROCONTROLLER, PBGA144 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB91F264BPF-G-E1 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller CMOS |
| MB91F264BPFV-G | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller CMOS |
| MB91F264BPFV-G-E1 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller CMOS |
| MB91F267 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontroller |
| MB91F267A | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。