- 您现在的位置：买卖IC网 > PDF目录80361 > MB91F465DAPVSR-GSE2 (FUJITSU LTD) 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP208 PDF资料下载
参数资料
| 型号： | MB91F465DAPVSR-GSE2 |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP208 |
| 封装： | 28 X 28 MM, 3.95 MM HEIGHT, 0.50 MM PITCH, LEAD FREE, PLASTIC, QFP-208 |
| 文件页数： | 58/141页 |
| 文件大小： | 3018K |
| 代理商： | MB91F465DAPVSR-GSE2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页当前第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页
MB91460D Series
23
6.
Mode pins (MD_x)
These pins should be connected directly to the power supply or ground pins. To prevent the device from entering
test mode accidentally due to noise, minimize the lengths of the patterns between each mode pin and power
supply pin or ground pin on the printed circuit board as possible and connect them with low impedance.
7.
Notes on operating in PLL clock mode
If the oscillator is disconnected or the clock input stops when the PLL clock is selected, the microcontroller may
continue to operate at the free-running frequency of the self-oscillating circuit of the PLL. However, this self-
running operation cannot be guaranteed.
8.
Pull-up control
The AC standard is not guaranteed in case a pull-up resistor is connected to the pin serving as an external bus pin.
9.
Notes on PS register
As the PS register is processed in advance by some instructions, when the debugger is being used, the exception
handling may result in execution breaking in an interrupt handling routine or the displayed values of the ags in
the PS register being updated.
As the microcontroller is designed to carry out reprocessing correctly upon returning from such an EIT event,
the operation before and after the EIT always proceeds according to specication.
The following behavior may occur if any of the following occurs in the instruction
immediately after a DIV0U/DIV0S instruction:
(a) a user interrupt or NMI is accepted;
(b) single-step execution is performed;
(c) execution breaks due to a data event or from the emulator menu.
1. D0 and D1 flags are updated in advance.
2. An EIT handling routine (user interrupt/NMI or emulator) is executed.
3. Upon returning from the EIT, the DIV0U/DIV0S instruction is executed
and the D0 and D1 ags are updated to the same values as those in 1.
The following behavior occurs when an ORCCR, STILM, MOV Ri,PS instruction is executed
to enable a user interrupt or NMI source while that interrupt is in the active state.
1. The PS register is updated in advance.
2. An EIT handling routine (user interrupt/NMI or emulator) is executed.
3. Upon returning from the EIT, the above instructions are executed and the PS register
is updated to the same value as in 1.
相关PDF资料 |
PDF描述 |
|---|---|
| M30280F8WG-U5 | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PBGA85 |
| M30620SPFP | 16-BIT, 24 MHz, MICROCONTROLLER, PQFP100 |
| M30626FHPFP-D9 | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100 |
| M30627FHPGP-D9 | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP128 |
| M3062CM8T-XXXGP | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB91F465KBPMT-GSE2 | 制造商:FUJITSU 功能描述: |
| MB91F465PAPMC-GSE2 | 制造商:FUJITSU 功能描述: |
| MB91F465X | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:The Ultimate Automotive Network |
| MB91F465XAPMC-ESE2 | 制造商:FUJITSU 功能描述: |
| MB91F465XAPMC-GE1 | 制造商:FUJITSU 功能描述: |
发布紧急采购，3分钟左右您将得到回复。