- 您现在的位置：买卖IC网 > PDF目录45194 > MB91F479BGL-GE1 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PBGA144 PDF资料下载
参数资料
| 型号： | MB91F479BGL-GE1 |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PBGA144 |
| 封装： | 12 X 12 MM, 1.45 MM HEIGHT, 0.80 MM PITCH, PLASTIC, FBGA-144 |
| 文件页数： | 18/92页 |
| 文件大小： | 2431K |
| 代理商： | MB91F479BGL-GE1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
MB91470/480 Series
DS07-16901-5E
25
■ HANDLING DEVICES
Preventing latch-up
Latch-up phenomenon may occur with CMOS IC, when a voltage higher than VCC or lower than VSS is applied
to either the input or output terminals, or when a voltage is applied between VCC pin and VSS pin that exceeds the
rated voltage. When latch-up occurs, a significant power-supply current surge results, which may damage some
elements due to the excess heat, so great care must be taken to ensure that the maximum rating is never
exceeded during use.
Treatment of unused input pins
Do not leave an unused input pin open, since it may cause a malfunction. Handle by, for example, using a
pull-up or pull-down resistor.
Power pins
In products with multiple VCC and VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to the same potential power
supply and a ground line externally to lower the electro-magnetic emission level, to prevent abnormal operation
of strobe signals caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic capacitor of approximately 0.1
F as a bypass capacitor between VCC
and VSS near this device.
Crystal oscillator circuit
Noise near the X0 and X1 pins may cause the device to malfunction. Design the printed circuit board so that X0,
X1, the crystal oscillator (or ceramic oscillator), and the bypass capacitor to ground are located as close to the
device as possible.
It is strongly recommended to design the PC board artwork with the X0 and X1pins surrounded by ground plane
because stable operation can be expected with such a layout. Please ask the crystal maker to evaluate the
oscillational characteristics of the crystal and this device.
About mode pins (MD0 to MD2)
These pins should be connected directly to VCC pin or VSS pin.
Design the printed circuit board such that the pull-up/down resistance stays low, as well as the distance between
the mode pins and power supply or GND pins is as short as possible and the connection impedance is low,
when the pins are pulled-up/down such as for switching the pin level and rewriting the Flash memory data. It is
because of preventing the device erroneously switching to test mode due to noise.
Operation at start-up
Be sure to execute setting initialized reset (INIT) with INITX pin immediately after start-up.
Immediately after that, also, hold the "L"-level input to the INITX pin for the stabilization wait time required for the
oscillator circuit to take the oscillation stabilization wait time for the oscillator circuit and the stabilization wait
time for the regulator (For INIT via the INITX pin, the oscillation stabilization wait time setting is initialized to the
minimum value).
相关PDF资料 |
PDF描述 |
|---|---|
| MB91F482PMC-GE1 | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91487PF-GE1 | 32-BIT, MROM, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91F487PF-GE1 | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91F486PF-GE1 | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91487PMC-GE1 | 32-BIT, MROM, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB91F479PM1RGE1 | 制造商:FUJITSU 功能描述:Pb Free |
| MB91F479PM1R-GE1 | 制造商:FUJITSU 功能描述: 制造商:FUJITSU 功能描述:MCU 32BIT FR 512K FLASH 144QFP |
| MB91F479PMC1-GE1 | 功能描述:IC MCU 512KB FLASH 144-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:FR MB91470 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| MB91F482PMC-GE1 | 功能描述:IC MCU 256KB FLASH 100-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:FR MB91480 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| MB91F487 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:32-bit Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。