- 您现在的位置：买卖IC网 > PDF目录45196 > MB95F156MPMC 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP52 PDF资料下载
参数资料
| 型号： | MB95F156MPMC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP52 |
| 封装： | 10 X 10 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LFQFP-52 |
| 文件页数： | 5/68页 |
| 文件大小： | 2246K |
| 代理商： | MB95F156MPMC |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
MB95150M Series
DS07-12613-4E
13
■ HANDLING DEVICES
Preventing Latch-up
Care must be taken to ensure that maximum voltage ratings are not exceeded when they are used.
Latch-up may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-withstand voltage pins or if higher than the rating voltage is applied between VCC
pin and VSS pin.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements.
Stable Supply Voltage
Supply voltage should be stabilized.
A sudden change in power-supply voltage may cause a malfunction even within the guaranteed operating range
of the Vcc power-supply voltage.
For stabilization, in principle, keep the variation in Vcc ripple (p-p value) in a commercial frequency range
(50/60 Hz) not to exceed 10% of the standard Vcc value and suppress the voltage variation so that the transient
variation rate does not exceed 0.1 V/ms during a momentary change such as when the power supply is switched.
Precautions for Use of External Clock
Even when an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from sub clock mode or stop mode.
Serial communication
There is a possibility to receive wrong data due to noise or other causes on the serial communication.
Therefore, design a printed circuit board so as to avoid noise.
Consider receiving of wrong data when designing the system. For example apply a checksum and retransmit
the data if an error occurs.
■ PIN CONNECTION
Treatment of Unused Pin
Leaving unused input pins unconnected can cause abnormal operation or latch-up, leaving to permanent dam-
age. Unused input pins should always be pulled up or down through resistance of at least 2 k
Ω. Any unused
input/output pins may be set to output mode and left open, or set to input mode and treated the same as unused
input pins. If there is unused output pin, make it to open.
Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1
μF between VCC and VSS pins
near this device.
相关PDF资料 |
PDF描述 |
|---|---|
| MB95F156NPMC | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP52 |
| MB95F156JPMT | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP48 |
| MB95F156NPMT | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP48 |
| MB95F168NPMC1 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP64 |
| MB95F168JPMC1 | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB95F156MPMT | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Microcontroller |
| MB95F156N | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Microcontroller |
| MB95F156NPMC | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Microcontroller |
| MB95F156NPMT | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Microcontroller |
| MB95F166D | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。