- 您现在的位置：买卖IC网 > PDF目录133001 > MB95F564HPFT-G-JNE2 (FUJITSU LTD) MICROCONTROLLER, PDSO20 PDF资料下载
参数资料
| 型号： | MB95F564HPFT-G-JNE2 |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | MICROCONTROLLER, PDSO20 |
| 封装： | 4.40 X 6.50 MM, 1.20 MM HEIGHT, 0.65 MM PITCH, PLASTIC, M10, TSSOP-20 |
| 文件页数： | 16/84页 |
| 文件大小： | 3929K |
| 代理商： | MB95F564HPFT-G-JNE2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
MB95560H/570H/580H Series
DS702-00010-1v0-E
23
■ NOTES ON DEVICE HANDLING
Preventing latch-ups
When using the device, ensure that the voltage applied does not exceed the maximum voltage rating.
In a CMOS IC, if a voltage higher than VCC or a voltage lower than VSS is applied to an input/output pin that
is neither a medium-withstand voltage pin nor a high-withstand voltage pin, or if a voltage out of the rating
range of power supply voltage mentioned in "1. Absolute Maximum Ratings" of "
When a latch-up occurs, power supply current increases significantly, which may cause a component to be
thermally destroyed.
Stabilizing supply voltage
Supply voltage must be stabilized.
A malfunction may occur when power supply voltage fluctuates rapidly even though the fluctuation is within
the guaranteed operating range of the VCC power supply voltage.
As a rule of voltage stabilization, suppress voltage fluctuation so that the fluctuation in VCC ripple (p-p value)
at the commercial frequency (50 Hz/60 Hz) does not exceed 10% of the standard VCC value, and the transient
fluctuation rate does not exceed 0.1 V/ms at a momentary fluctuation such as switching the power supply.
Notes on using the external clock
When an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from subclock mode or stop mode.
■ PIN CONNECTION
Treatment of unused pins
If an unused input pin is left unconnected, a component may be permanently damaged due to malfunctions
or latch-ups. Always pull up or pull down an unused input pin through a resistor of at least 2 k
Ω. Set an
unused input/output pin to the output state and leave it unconnected, or set it to the input state and treat it
the same as an unused input pin. If there is an unused output pin, leave it unconnected.
Power supply pins
To reduce unnecessary electro-magnetic emission, prevent malfunctions of strobe signals due to an increase
in the ground level, and conform to the total output current standard, always connect the VCC pin and the VSS
pin to the power supply and ground outside the device. In addition, connect the current supply source to the
VCC pin and the VSS pin with low impedance.
It is also advisable to connect a ceramic capacitor of approximately 0.1 F as a bypass capacitor between
the VCC pin and the VSS pin at a location close to this device.
DBG pin
Connect the DBG pin directly to an external pull-up resistor.
To prevent the device from unintentionally entering the debug mode due to noise, minimize the distance
between the DBG pin and the VCC or VSS pin when designing the layout of the printed circuit board.
The DBG pin should not stay at “L” level after power-on until the reset output is released.
RST pin
Connect the RST pin directly to an external pull-up resistor.
To prevent the device from unintentionally entering the reset mode due to noise, minimize the distance
between the RST pin and the VCC or VSS pin when designing the layout of the printed circuit board.
The RST/PF2 pin functions as the reset input/output pin after power-on. In addition, the reset output of the
RST/PF2 pin can be enabled by the RSTOE bit in the SYSC register, and the reset input function and the
general purpose I/O function can be selected by the RSTEN bit in the SYSC register.
相关PDF资料 |
PDF描述 |
|---|---|
| MB95F582KWQN-G-JNE1 | MICROCONTROLLER, PQCC32 |
| MAC7126CPV40 | 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP112 |
| MAC7131MVM40 | 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PBGA208 |
| MJE700T16 | 4 A, 60 V, PNP, Si, POWER TRANSISTOR, TO-220AB |
| MPS9484F | 50 V, PNP, Si, SMALL SIGNAL TRANSISTOR, TO-92 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB95F564KPF-G-JNE2 | 功能描述:IC MCU 8BIT 20KB FLASH 20TSSOP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:8FX MB95560H 标准包装:60 系列:PSOC® 3 CY8C38xx 核心处理器:8051 芯体尺寸:8-位 速度:67MHz 连通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外围设备:电容感应，DMA，LCD，POR，PWM，WDT 输入/输出数:25 程序存储器容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 电压 - 电源 (Vcc/Vdd):1.71 V ~ 5.5 V 数据转换器:A/D 2x20b，D/A 4x8b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:48-VFQFN 裸露焊盘 包装:托盘 |
| MB95F636HP-ES-SH-SNE2 | 制造商:FUJITSU 功能描述:8-bit MCU |
| MB95F636HPMC-ES-SNE2 | 制造商:FUJITSU 功能描述:8-bit FX series microcontroller |
| MB95F636HWQN-ES-SNE1 | 制造商:FUJITSU 功能描述:8-bit MCU |
| MB95F636KP-ES-SH-SNE2 | 制造商:FUJITSU 功能描述:8-bit FX series microcontroller |
发布紧急采购，3分钟左右您将得到回复。