- 您现在的位置：买卖IC网 > PDF目录45198 > MB95R203AP-G-SH-JNE2 (FUJITSU LTD) 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PDIP24 PDF资料下载
参数资料
| 型号： | MB95R203AP-G-SH-JNE2 |
| 厂商： | FUJITSU LTD |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PDIP24 |
| 封装： | 22.86 X 6.40 MM, 4.80 MM HEIGHT, 1.778 MM PITCH, PLASTIC, DIP-24 |
| 文件页数： | 3/48页 |
| 文件大小： | 1990K |
| 代理商： | MB95R203AP-G-SH-JNE2 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
MB95R203A
DS07-12630-1E
11
■ PIN CONNECTION
Treatment of Unused Input Pin
Leaving unused input pins unconnected can cause abnormal operation or latch-up, leaving to permanent dam-
age. Unused input pins should always be pulled up or down through resistance of at least 2 k
Ω. Any unused
input/output pins may be set to output mode and left open, or set to input mode and treated the same as unused
input pins. If there is unused output pin, make it to open.
Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance. It
is also advisable to connect a ceramic bypass capacitor of approximately 0.1
μF between VCC and VSS near this
device.
DBG Pin
Connect the DBG pin directly to external Pull-up.
To prevent the device unintentionally entering test mode due to noise, lay out the printed circuit board so as to
minimize the distance from the DBG pin to VCC or VSS pins.
The DBG pin should not stay at “L” level after power-on until the reset output is released.
RST Pin
Connect the RST pin directly to Pull-up.
To prevent the device unintentionally entering test mode due to noise, lay out the printed circuit board so as to
minimize the distance from the RST pin to VCC or VSS pins.
The RST/PF2 pin functions as the reset input/output pin after power-on. In addition, the reset output can be
enabled by the RSTOE bit of the SYSC register, and the reset input function or the general purpose I/O function
can be selected by the RSTEN bit of the SYSC register.
R
DBG
RST
R
Example of DBG / RST connection diagram
Pull-up resistor recommended
resistance
For DBG pin : R
= 4.7 kΩ
For RST pin : R
= 10 kΩ
相关PDF资料 |
PDF描述 |
|---|---|
| MB95R203APF-G-JNE2 | 8-BIT, 10 MHz, MICROCONTROLLER, PDSO20 |
| MB95R203P-G-SH-NE2 | 8-BIT, 10 MHz, MICROCONTROLLER, PDIP24 |
| MB96338YWAPMC-GSE2 | 16-BIT, MROM, 48 MHz, MICROCONTROLLER, PQFP144 |
| MB96338RSAPMC-GSE2 | 16-BIT, MROM, 48 MHz, MICROCONTROLLER, PQFP144 |
| MB96336YSAPMC-GSE2 | 16-BIT, MROM, 48 MHz, MICROCONTROLLER, PQFP144 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB95R203PF-G-JNE2 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers |
| MB95R203P-G-SH-JNE2 | 制造商:FUJITSU 功能描述:IC MCU 8BIT 8FX 8K FRAM 24SDIP |
| MB96300 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96310 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96320 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
发布紧急采购，3分钟左右您将得到回复。