- 您现在的位置：买卖IC网 > PDF目录262870 > MB96F326YSAPMC-GE2 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | MB96F326YSAPMC-GE2 |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 12 X 12 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LFQFP-80 |
| 文件页数： | 111/159页 |
| 文件大小： | 2625K |
| 代理商： | MB96F326YSAPMC-GE2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页当前第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页
Preliminary Specication
MB96300
FME/EMDC- 2007-02-12
MB96300_shortspec.fm
55
PRELIMINARY
s HANDLING DEVICES
Special care is required for the following when handling the device:
Preventing latch-up
Treatment of unused pins
Using external clock
Precautions for when not using a sub clock signal
Notes on during operation of PLL clock mode
Power supply pins (VCC/VSS)
Crystal Oscillator Circuit
Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs
Connection of Unused Pins of A/D Converter
Notes on Energization
Stabilization of power supply voltage
1.
Preventing latch-up
CMOS IC chips may suffer latch-up under the following conditions:
A voltage higher than VCC or lower than VSS is applied to an input or output pin.
A voltage higher than the rated voltage is applied between VCC and VSS.
The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current drastically, causing thermal damage to the device.
For the same reason, also be careful not to let the analog power-supply voltage (AVCC, AVRH) exceed the
digital power-supply voltage.
2.
Treatment of unused pins
Unused input pins may be left open when the input is disabled (corresponding bit of Port Input Enable register
PIER = 0).
Leaving unused input pins open when the input is enabled may result in misbehavior and possible permanent
damage of the device. Therefore they must be pulled up or pulled down through resistors. To prevent latchup,
those resistors should be more than 2 kOhm.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with either
input disabled or external pull-up/pull-down resistor as described above.
3.
Using external clock
To use external clock, drive the X0 pin and leave X1 pin open.
4.
Precautions for when not using a sub clock signal
If you do not connect pins X0A and X1A to an oscillator, use a pull-down resistor on the X0A pin, and
leave the X1A pin open.
5.
Notes on during operation of PLL clock mode
If the PLL clock mode is selected and no external oscillator is operating or no external clock is supplied, the
microcontroller attempts to be working with the freely oscillating PLL. Performance of this operation, however,
cannot be guaranteed.
6.
Power supply pins (VCC/VSS)
Ensure that all VCC-level power supply pins are at the same potential. In addition, ensure the same for all
VSS-level power supply pins. If there are more than one VCC or VSS system, the device may operate
incorrectly even within the guaranteed operating range.
相关PDF资料 |
PDF描述 |
|---|---|
| MB96F346RSAPQC-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP100 |
| MB95F126MBPF | 8-BIT, FLASH, 16.25 MHz, MICROCONTROLLER, PQFP100 |
| MB96384RWAPMC-GSE2 | 16-BIT, FLASH, 56 MHz, MICROCONTROLLER, PQFP120 |
| MC9S08DZ96F2-CLH | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 |
| MCIMX255AJM4A | 32-BIT, 400 MHz, MICROPROCESSOR, PBGA400 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB96F326YSBPMC-GSE2 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96F326YWAPMC-GE2 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96F326YWBPMC-GSE2 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96F336 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| MB96F336USAPMC-GSE2 | 制造商:FUJITSU 功能描述:MCU 16BIT 16FX 288K FLASH144LQFP |
发布紧急采购，3分钟左右您将得到回复。