参数资料
| 型号： | MC100E195FNR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC DELAY LINE 128TAP 28-PLCC |
| 产品变化通告： | Dimensional change 21/Oct/2008 |
| 标准包装： | 500 |
| 系列： | 100E |
| 标片/步级数： | 128 |
| 功能： | 可编程 |
| 延迟到第一抽头： | 1.39ns |
| 接头增量： | 20ps |
| 可用的总延迟： | 1.39ns ~ 3.63ns |
| 独立延迟数： | 1 |
| 电源电压： | 4.2 V ~ 5.7 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-LCC（J 形引线） |
| 供应商设备封装： | 28-PLCC（11.51x11.51） |
| 包装： | 带卷 (TR) |
MC10E195, MC100E195
http://onsemi.com
7
VCCO
ADDRESS BUS (A0A6)
A7
INPUT
D1
D0
LEN
VEE
IN
VBB
D2
D3
D4
D5
D6
D7
EN
SET
MIN
SET
MAX
CASCADE
VCC
VCCO
Q
D1
D0
LEN
VEE
IN
VBB
EN
SET
MIN
SET
MAX
CASCADE
VCC
VCCO
Q
VCCO
OUTPUT
D2
D3
D4
D5
D6
D7
E195
Chip #1
E195
Chip #2
Figure 3. Cascading Interconnect Architecture
Cascading Multiple E195’s
To increase the programmable range of the E195 internal
cascade circuitry has been included. This circuitry allows for
the cascading of multiple E195’s without the need for any
external gating. Furthermore this capability requires only
one more address line per added E195. Obviously cascading
multiple PDC’s will result in a larger programmable range
however this increase is at the expense of a longer minimum
delay.
Figure 3 illustrates the interconnect scheme for cascading
two E195’s. As can be seen, this scheme can easily be
expanded for larger E195 chains. The D7 input of the E195
is the cascade control pin. With the interconnect scheme of
Figure 3 when D7 is asserted it signals the need for a larger
programmable range than is achievable with a single device.
An expansion of the latch section of the block diagram is
pictured below. Use of this diagram will simplify the
explanation of how the cascade circuitry works. When D7
of chip #1 above is low the cascade output will also be low
while the cascade bar output will be a logical high. In this
condition the SET MIN pin of chip #2 will be asserted and
thus all of the latches of chip #2 will be reset and the device
will be set at its minimum delay. Since the RESET and SET
inputs of the latches are overriding any changes on the
A0A6 address bus will not affect the operation of chip #2.
Chip #1 on the other hand will have both SET MIN and
SET MAX de-asserted so that its delay will be controlled
entirely by the address bus A0A6. If the delay needed is
greater than can be achieved with 31.75 gate delays
(1111111 on the A0A6 address bus) D7 will be asserted to
signal the need to cascade the delay to the next E195 device.
When D7 is asserted the SET MIN pin of chip #2 will be
de-asserted and the delay will be controlled by the A0A6
address bus. Chip #1 on the other hand will have its SET
MAX pin asserted resulting in the device delay to be
independent of the A0A6 address bus.
When the SET MAX pin of chip #1 is asserted the D0 and
D1 latches will be reset while the rest of the latches will be
set. In addition, to maintain monotonicity an additional gate
delay is selected in the cascade circuitry. As a result when D7
of chip #1 is asserted the delay increases from 31.75 gates
to 32 gates. A 32 gate delay is the maximum delay setting for
the E195.
To expand this cascading scheme to more devices one
simply needs to connect the D7 input and CASCADE
outputs of the current most significant E195 to the new most
significant E195 in the same manner as pictured in Figure 3.
The only addition to the logic is the increase of one line to
the address bus for cascade control of the second PDC.
SET MIN
SET MAX
TO SELECT MULTIPLEXERS
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
D0
Q0
LEN
Reset Reset
D1
Q1
D2
Q2
D3
Q3
D4
Q4
D5
Q5
D6
Q6
D7
Q7
LEN
CASCADE
Figure 4. Expansion of the Latch Section of the E195 Block Diagram
Reset Reset
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2WK-MX-B1 | CONVERTER MOD DC/DC 40V 75W |
| SY55856UHG TR | IC DELAY LINE 7TAP 32-TQFP |
| M83723/76R18086 | CONN PLUG 8POS STRAIGHT W/PINS |
| SY89296UMG | IC DELAY LINE 1024TAP 32-MLF |
| MS27484T24A35PA | CONN PLUG 128POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC100E196 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:PROGRAMMABLE DELAY CHIP |
| MC100E196FN | 功能描述:延迟线/计时元素 5V ECL Programmable RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 传播延迟时间:1000 ps 工作温度范围: 封装 / 箱体:QFN-24 封装:Tube |
| MC100E196FNG | 功能描述:延迟线/计时元素 5V ECL Programmable Delay RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 传播延迟时间:1000 ps 工作温度范围: 封装 / 箱体:QFN-24 封装:Tube |
| MC100E196FNR2 | 功能描述:延迟线/计时元素 5V ECL Programmable RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 传播延迟时间:1000 ps 工作温度范围: 封装 / 箱体:QFN-24 封装:Tube |
| MC100E196FNR2G | 功能描述:延迟线/计时元素 5V ECL Programmable Delay RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 传播延迟时间:1000 ps 工作温度范围: 封装 / 箱体:QFN-24 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。