参数资料
| 型号： | MC10E016FNR2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC COUNTER 8BIT SYNC ECL 28-PLCC |
| 产品变化通告： | Reactivation Notice 26/Apr/2011 Product Obsolescence 08/Apr/2011 |
| 标准包装： | 500 |
| 系列： | 10E |
| 逻辑类型： | 二进制计数器 |
| 方向： | 上 |
| 元件数： | 1 |
| 每个元件的位元数： | 8 |
| 复位： | 异步 |
| 计时： | 同步 |
| 计数速率： | 900MHz |
| 触发器类型： | 正边沿 |
| 电源电压： | 4.2 V ~ 5.7 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-LCC（J 形引线） |
| 供应商设备封装： | 28-PLCC（11.51x11.51） |
| 包装： | 带卷 (TR) |
MC10E016, MC100E016
http://onsemi.com
9
APPLICATIONS INFORMATION (continued)
E016
MSB
CLK
TC
PE
CE
E016
CLK
TC
PE
CE
E016
CLK
TC
PE
CE
EL01
CLOCK
Q0 > Q7
PO > P7
Q0 > Q7
PO > P7
Q0 > Q7
PO > P7
Q0 > Q7
PO > P7
LO
E016
LSB
CLK
TC
PE
CE
Figure 6. 32Bit Cascaded E016 Programmable Divider
OUT
Figure 6 shows a typical block diagram of a 32bit divider
chain. Once again to maximize the frequency of operation
EL01 OR gates were used. For lower frequency applications
a slower OR gate could replace the EL01. Note that for a
16bit divider the OR function feeding the PE (program
enable) input CANNOT be replaced by a wire OR tie as the
TC output of the least significant E016 must also feed the CE
input of the most significant E016. If the two TC outputs
were OR tied the cascaded count operation would not
operate properly. Because in the cascaded form the PE
feedback is external and requires external gating, the
maximum frequency of operation will be significantly less
than the same operation in a single device.
Maximizing E016 Count Frequency
The E016 device produces 9 fast transitioning
singleended outputs, thus VCC noise can become
significant in situations where all of the outputs switch
simultaneously in the same direction. This VCC noise can
negatively impact the maximum frequency of operation of
the device. Since the device does not need to have the Q
outputs terminated to count properly, it is recommended that
if the outputs are not going to be used in the rest of the system
they should be left unterminated. In addition, if only a subset
of the Q outputs are used in the system only those outputs
should be terminated. Not terminating the unused outputs
will not only cut down the VCC noise generated but will also
save in total system power dissipation. Following these
guidelines will allow designers to either be more aggressive
in their designs or provide them with an extra margin to the
published data book specifications.
相关PDF资料 |
PDF描述 |
|---|---|
| MC10E136FNR2 | IC COUNTER U/D 6BIT UNIV 28-PLCC |
| MC10E137FNR2 | IC RIPPLE COUNTER 8BIT HS 28PLCC |
| MC10E431FNR2 | IC FLIP FLOP 3BIT 5V ECL 28-PLCC |
| MC10E451FNR2 | IC FLIP FLOP 6BIT 5V ECL 28-PLCC |
| MC10EL31DTR2 | IC FLIP FLOP SET/RST ECL 8-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC10E016FNR2G | 功能描述:计数器 IC 5V ECL 8-Bit Binary Up Synchronous RoHS:否 制造商:NXP Semiconductors 计数器类型:Binary Counters 逻辑系列:74LV 位数:10 计数法: 计数顺序: 工作电源电压:1 V to 5.5 V 工作温度范围:- 40 C to + 125 C 封装 / 箱体:SOT-109 封装:Reel |
| MC10E101 E27G WAF | 制造商:ON Semiconductor 功能描述: |
| MC10E101FN | 功能描述:逻辑门 Quad 4-Input OR/NOR RoHS:否 制造商:Texas Instruments 产品:OR 逻辑系列:LVC 栅极数量:2 线路数量（输入/输出）:2 / 1 高电平输出电流:- 16 mA 低电平输出电流:16 mA 传播延迟时间:3.8 ns 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:DCU-8 封装:Reel |
| MC10E101FNG | 功能描述:逻辑门 Quad 4-Input OR/NOR RoHS:否 制造商:Texas Instruments 产品:OR 逻辑系列:LVC 栅极数量:2 线路数量（输入/输出）:2 / 1 高电平输出电流:- 16 mA 低电平输出电流:16 mA 传播延迟时间:3.8 ns 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:DCU-8 封装:Reel |
| MC10E101FNR2 | 功能描述:逻辑门 Quad 4-Input OR/NOR RoHS:否 制造商:Texas Instruments 产品:OR 逻辑系列:LVC 栅极数量:2 线路数量（输入/输出）:2 / 1 高电平输出电流:- 16 mA 低电平输出电流:16 mA 传播延迟时间:3.8 ns 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:DCU-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。