参数资料
型号: MC10SX1130DG
厂商: ON Semiconductor
文件页数: 5/9页
文件大小: 0K
描述: IC LED DRIVER LINEAR 16-SOIC
标准包装: 48
输出数: 1
内部驱动器:
类型 - 主要: 通用
频率: 300MHz
电源电压: +5V,-5.2V
安装类型: 表面贴装
封装/外壳: 16-SOIC(0.154",3.90mm 宽)
供应商设备封装: 16-SOIC
包装: 管件
工作温度: -40°C ~ 85°C
其它名称: MC10SX1130DGOS
MC10SX1130
Table 4. AC CHARACTERISTICS (RTCO = 1 k W ± 5%, R SET = R at I OUT = R at I OUT = 10 W ± 1%, Unless Otherwise Noted) (Note 5)
? 40 ° C
0 to 85 ° C
Symbol
Characteristic
Condition
Min
Typ
Max
Min
Typ
Max
Unit
t PLH ,
t PHL
Propagation Delay (Differential)
to Output (Single ? Ended)
1300
1300
1000
950
1400
1400
1800
1850
ns
t Stretch
t r 10 ? 90
t f 90 ? 10
t r 20 ? 80
t f 80 ? 20
Jitter
BW
t SKEW
V PP
Propagation Delay Stretch = OPEN
Stretch = V CC
Stretch = V EE
Rise Time
Fall Time
Rise Time
Fall Time
Jitter
Square Wave Input
Pseudo Random Input
Bandwidth
Duty Cycle Skew
(Differential)
Minimum Input Swing
(Note 6)
10% to 90%
90% to 10%
20% to 80%
80% to 20%
(Note 7)
(Note 8)
(Note 9)
(Note 10)
300
150
0
145
300
600
375
490
260
9
10
400
± 30
120
250
510
330
360
220
300
150
0
155
310
880
550
600
500
6
15
400
± 30
200
380
1260
860
850
750
ps
ps
ps
ps
MHz
ps
mV
V CMR
Common Mode Range
(Note 11)
? 0.400
See 7
? 0.400
See 7
V
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
5. 10SX circuits are designed to meet the AC specifications shown in the table after thermal equilibrium has been established. The circuit is
mounted in a test socket or mounted on a printed circuit board and transverse air greater than 500 lfm is maintained.
6. When the Stretch function is used, the output low pulse width is increased by the specified amount.
7. Test condition uses a 133 MHz 50% duty cycle signal.
8. Test condition uses a 266 Mbit/s input pseudo-random data stream (n = 23).
9. Duty cycle skew is the difference between t PLH and t PHL propagation delay through a device, Stretch input is left open.
10. Minimum input swing for which AC parameters are guaranteed.
11. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls
within the specified range and the peak-to-peak voltage lies between V PP Min and 1.0 V. The lower end of the CMR range is dependent on
V EE and is equal to V EE + 3.5 V.
http://onsemi.com
5
相关PDF资料
PDF描述
REC3-1205DRW/H/B/M CONV DC/DC 3W 9-18VIN +/-05VOUT
ESC60DRTI CONN EDGECARD 120PS DIP .100 SLD
ECC12DJCN-S1136 CONN EDGECARD 24PS .100 PRESSFIT
EMC49DRTH CONN EDGECARD 98POS .100 EXTEND
RBC07DRYN CONN EDGECARD 14POS DIP .100 SLD
相关代理商/技术参数
参数描述
MC10SX1130DR2 功能描述:LED照明驱动器 BBG ECL COAX CABL RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MC10SX1130DR2G 功能描述:LED照明驱动器 BBG ECL COAX CABL RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MC10SX1189D 功能描述:缓冲器和线路驱动器 Fiber Channel Coax RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel
MC10SX1189DG 功能描述:缓冲器和线路驱动器 Fiber Channel Coax Calbe Driver RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel
MC10SX1189DR2 功能描述:缓冲器和线路驱动器 Fiber Channel Coax RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel