参数资料
| 型号： | MC10SX1190DT |
| 厂商： | ON Semiconductor |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER COAX CABLE 20TSSOP |
| 标准包装： | 75 |
| 类型： | 驱动器 |
| 驱动器/接收器数： | 1/0 |
| 电源电压： | 3 V ~ 3.6 V，4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 其它名称： | MC10SX1190DTOS |
MC10SX1190
http://onsemi.com
4
Table 4. AC CHARACTERISTICS (VCC = 3.0 V to 5.5 V, VEE = 0 V) (Note 11)
40°C
25°C to 85°C
Symbol
Characteristic
Min
Typ
Max
Min
Typ
Max
Unit
tpd
Propagation DelaytoOutput
DR → QR (Diff) (Notes 12 and 13)
140
240
340
180
280
380
ps
DR → QT (Diff)
300
400
500
350
470
650
DT → QT (Diff)
280
380
480
350
440
650
tPLH,
tPHL
Propagation Delay
SEL → QT,QT
(1.5 V to 50% Pt)
400
700
1000
400
700
1000
ps
tr,
tf
Rise Time (20% to 80%)
QR,QR
Fall Time (80% to 20%)
70
140
200
90
155
250
ps
tr,
tf
Rise Time (20% to 80%)
QT,QT
Fall Time 80% to 20%
150
200
280
150
230
500
ps
tskew
Within Device Skew (Note 14)
15
ps
VPP
Input Swing (Differential Configuration)
200
1000
200
1000
mV
VCMR
Common Mode Range (Note 15)
3.0
4.35
3.0
4.35
V
fmax
Maximum Operation Frequency
2.5
Gb/s
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
11. VEE can vary +0.3 V to 0.3 V
12.The differential propagation delay is defined as the delay from the crossing points of the differential input signals to the crossing point of the
differential output signals.
13.The single-ended propagation delay is defined as the delay from the 50% point of the input signal to the 50% point of the output signal.
14.Duty cycle skew is the difference between tPLH and tPHL propagation delay through a device.
15.The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls
within the specified range and the peak-to-peak voltage lies between VPP Min and 1.0 V.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX158ACWI+T | IC ADC 8BIT 8CH W/MUX&REF 28SOIC |
| MS3122E14-15S | CONN RCPT 15POS BOX MOUNT W/SCKT |
| VE-B71-MW-F1 | CONVERTER MOD DC/DC 12V 100W |
| MAX1188CCUP+ | IC ADC 16BIT 135KSPS 20-TSSOP |
| VE-JNJ-MX-F2 | CONVERTER MOD DC/DC 36V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC10SX1190DTG | 功能描述:缓冲器和线路驱动器 Fiber Channel Coax Calbe Driver RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| MC10SX1190DTR2 | 功能描述:缓冲器和线路驱动器 Fiber Channel Coax RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| MC10SX1190DTR2G | 功能描述:缓冲器和线路驱动器 Fiber Channel Coax Calbe Driver RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| MC-10X1.25 | 制造商:Components Corporation 功能描述: |
| MC10XS3412CHFK | 功能描述:电源开关 IC - 配电 ESWITCH GEN3 1012 RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。