参数资料
| 型号： | MC14541BDR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | IC OSC PROG TIMER 3MHZ 14SOIC |
| 标准包装： | 1 |
| 类型： | 可编程计时器 |
| 频率： | 3MHz |
| 电源电压： | 3 V ~ 18 V |
| 电流 - 电源： | 15µA |
| 工作温度： | -55°C ~ 125°C |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 包装： | 标准包装 |
| 供应商设备封装： | 14-SOICN |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 1125 (CN2011-ZH PDF) |
| 其它名称： | MC14541BDR2GOSDKR |
MC14541B
http://onsemi.com
6
TYPICAL RC OSCILLATOR CHARACTERISTICS
Figure 4. RC Oscillator Stability
Figure 5. RC Oscillator Frequency as a
Function of Rtc and Ctc
8.0
4.0
0
-4.0
-8.0
-12
-16
125
100
75
50
25
0
-25
-55
TA, AMBIENT TEMPERATURE (°C)
FREQUENCY
DEVIA
TION
(%)
VDD = 15 V
10 V
5.0 V
RS = 0, f = 10.15 kHz @ VDD = 10 V, TA = 25°C
RS = 120 kW, f = 7.8 kHz @ VDD = 10 V, TA = 25°C
RTC = 56 kW,
C = 1000 pF
100
0.1
0.2
0.5
1.0
2.0
5.0
10
20
50
1.0 k
10 k
100 k
1.0 m
f,OSCILLA
T
OR
FREQUENCY
(kHz)
RTC, RESISTANCE (OHMS)
0.0001
0.001
0.01
0.1
C, CAPACITANCE (
mF)
VDD = 10 V
f AS A FUNCTION
OF RTC
(C = 1000 pF)
(RS ≈ 2RTC)
f AS A FUNCTION
OF C
(RTC = 56 kW)
(RS = 120 kW)
OPERATING CHARACTERISTICS
With Auto Reset pin set to a “0” the counter circuit is
initialized by turning on power. Or with power already on,
the counter circuit is reset when the Master Reset pin is set
to a “1”. Both types of reset will result in synchronously
resetting all counter stages independent of counter state.
Auto Reset pin when set to a “1” provides a low power
operation.
The RC oscillator as shown in Figure 3 will oscillate with
a frequency determined by the external RC network i.e.,
if (1 kHz v f v 100 kHz)
2.3 RtcCtc
1
f =
and RS ≈ 2 Rtc
where RS ≥ 10 kW
The time select inputs (A and B) provide a twobit address
to output any one of four counter stages (28, 210, 213 and
216). The 2n counts as shown in the Frequency Selection
Table represents the Q output of the Nth stage of the counter.
When A is “1”, 216 is selected for both states of B. However,
when B is “0”, normal counting is interrupted and the 9th
counter stage receives its clock directly from the oscillator
(i.e., effectively outputting 28).
The Q/Q select output control pin provides for a choice of
output level. When the counter is in a reset condition and
Q/Q select pin is set to a “0” the Q output is a “0”,
correspondingly when Q/Q select pin is set to a “1” the Q
output is a “1”.
When the mode control pin is set to a “1”, the selected
count is continually transmitted to the output. But, with
mode pin “0” and after a reset condition the RS flipflop (see
Expanded Block Diagram) resets, counting commences,
and after 2n1 counts the RS flipflop sets which causes the
output to change state. Hence, after another 2n1 counts the
output will not change. Thus, a Master Reset pulse must be
applied or a change in the mode pin level is required to reset
the single cycle operation.
DIGITAL TIMER APPLICATION
Rtc
Ctc
NC
RS
AR
MR
INPUT
tMR
VDD
B
A
N.C.
OUTPUT
VDD
MODE
Q/Q
t + tMR
1
2
3
4
5
6
78
9
10
11
12
13
14
When Master Reset (MR) receives a positive pulse, the
internal counters and latch are reset. The Q output goes high
and remains high until the selected (via A and B) number of
clock pulses are counted, the Q output then goes low and
remains low until another input pulse is received.
This “one shot” is fully retriggerable and as accurate as the
input frequency. An external clock can be used (pin 3 is the
clock input, pins 1 and 2 are outputs) if additional accuracy
is needed.
Notice that a setup time equal to the desired pulse width
output is required immediately following initial power up,
during which time Q output will be high.
相关PDF资料 |
PDF描述 |
|---|---|
| LM555CMX | IC OSC MONO TIMING 8-SOP |
| VE-B33-IU-S | CONVERTER MOD DC/DC 24V 200W |
| 74VHC157MTCX | MULTIPLEXER QUAD 2IN 16TSSOP |
| VI-B1N-IU-S | CONVERTER MOD DC/DC 18.5V 200W |
| VI-B1H-IU-S | CONVERTER MOD DC/DC 52V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC14541BDR2G-CUT TAPE | 制造商:ON 功能描述:MC14541B Series 3 to 18 Vdc Programmable Oscillator-Timer - SOIC-14 |
| MC14541BDT | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MC14541BDTR2 | 功能描述:计时器和支持产品 LOG CMOS OSILATR TIMER RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| MC14541BDTR2G | 功能描述:计时器和支持产品 LOG CMOS OSILATR TIMER RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| MC14541BF | 功能描述:计时器和支持产品 LOG CMOS OSILATR TIMER RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。