- 您现在的位置：买卖IC网 > PDF目录65809 > MC14541BFR2 (ON SEMICONDUCTOR) 1 TIMER(S), PROGRAMMABLE TIMER, PDSO14 PDF资料下载
参数资料
| 型号： | MC14541BFR2 |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 1 TIMER(S), PROGRAMMABLE TIMER, PDSO14 |
| 封装： | EIAJ, PLASTIC, SOIC-14 |
| 文件页数： | 7/10页 |
| 文件大小： | 163K |
| 代理商： | MC14541BFR2 |
MC14541B
http://onsemi.com
6
TYPICAL RC OSCILLATOR CHARACTERISTICS
Figure 4. RC Oscillator Stability
Figure 5. RC Oscillator Frequency as a
Function of Rtc and Ctc
8.0
4.0
0
4.0
8.0
12
16
125
100
75
50
25
0
25
55
TA, AMBIENT TEMPERATURE (°C)
FREQUENCY
DEVIA
TION
(%)
VDD = 15 V
10 V
5.0 V
RS = 0, f = 10.15 kHz @ VDD = 10 V, TA = 25°C
RS = 120 kW, f = 7.8 kHz @ VDD = 10 V, TA = 25°C
RTC = 56 kW,
C = 1000 pF
100
0.1
0.2
0.5
1.0
2.0
5.0
10
20
50
1.0 k
10 k
100 k
1.0 m
f,OSCILLA
TOR
FREQUENCY
(kHz)
RTC, RESISTANCE (OHMS)
0.0001
0.001
0.01
0.1
C, CAPACITANCE (mF)
VDD = 10 V
f AS A FUNCTION
OF RTC
(C = 1000 pF)
(RS ≈ 2RTC)
f AS A FUNCTION
OF C
(RTC = 56 kW)
(RS = 120 kW)
OPERATING CHARACTERISTICS
With Auto Reset pin set to a “0” the counter circuit is
initialized by turning on power. Or with power already on,
the counter circuit is reset when the Master Reset pin is set
to a “1”. Both types of reset will result in synchronously
resetting all counter stages independent of counter state.
Auto Reset pin when set to a “1” provides a low power
operation.
The RC oscillator as shown in Figure 3 will oscillate with
a frequency determined by the external RC network i.e.,
if (1 kHz v f v 100 kHz)
2.3 RtcCtc
1
f =
and RS ≈ 2 Rtc
where RS ≥ 10 kW
The time select inputs (A and B) provide a twobit address
to output any one of four counter stages (28, 210, 213 and
216). The 2n counts as shown in the Frequency Selection
Table represents the Q output of the Nth stage of the counter.
When A is “1”, 216 is selected for both states of B. However,
when B is “0”, normal counting is interrupted and the 9th
counter stage receives its clock directly from the oscillator
(i.e., effectively outputting 28).
The Q/Q select output control pin provides for a choice of
output level. When the counter is in a reset condition and
Q/Q select pin is set to a “0” the Q output is a “0”,
correspondingly when Q/Q select pin is set to a “1” the Q
output is a “1”.
When the mode control pin is set to a “1”, the selected
count is continually transmitted to the output. But, with
mode pin “0” and after a reset condition the RS flipflop (see
Expanded Block Diagram) resets, counting commences,
and after 2n1 counts the RS flipflop sets which causes the
output to change state. Hence, after another 2n1 counts the
output will not change. Thus, a Master Reset pulse must be
applied or a change in the mode pin level is required to reset
the single cycle operation.
DIGITAL TIMER APPLICATION
Rtc
Ctc
NC
RS
AR
MR
INPUT
tMR
VDD
B
A
N.C.
OUTPUT
VDD
MODE
Q/Q
t + tMR
1
2
3
4
5
6
78
9
10
11
12
13
14
When Master Reset (MR) receives a positive pulse, the
internal counters and latch are reset. The Q output goes high
and remains high until the selected (via A and B) number of
clock pulses are counted, the Q output then goes low and
remains low until another input pulse is received.
This “one shot” is fully retriggerable and as accurate as the
input frequency. An external clock can be used (pin 3 is the
clock input, pins 1 and 2 are outputs) if additional accuracy
is needed.
Notice that a setup time equal to the desired pulse width
output is required immediately following initial power up,
during which time Q output will be high.
相关PDF资料 |
PDF描述 |
|---|---|
| MC2842-11-1 | 0.1 A, SILICON, SIGNAL DIODE |
| MC2844-T11-1 | 0.1 A, SILICON, SIGNAL DIODE |
| MC68901FNR2 | MULTIFUNCTION PERIPHERAL, PQCC52 |
| MC68HC05E5DW | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28 |
| MC68HC11F1FN | 8-BIT, EEPROM, MICROCONTROLLER, PQCC68 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC145423DT | 功能描述:IC TXRX UDLT/ISDN 28TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC145423EG | 制造商:Freescale Semiconductor 功能描述:DATACOM, DIGITAL SLIC, 28 Pin Plastic SMT |
| MC145423EGR2 | 制造商:Freescale Semiconductor 功能描述:DATACOM, DIGITAL SLIC, 28 Pin Plastic SMT |
| MC145423EJ | 功能描述:IC TXRX UDLT/ISDN 28-TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
| MC145425P | 制造商:Motorola Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。