参数资料
型号: MC145481ENR2
厂商: Freescale Semiconductor
文件页数: 18/24页
文件大小: 0K
描述: IC CODEC-FILTER PCM 3V 20-SSOP
标准包装: 1,500
类型: PCM 编解码器/滤波器
数据接口: PCM 音频接口
分辨率(位): 6 b
ADC / DAC 数量: 1 / 1
三角积分调变:
电压 - 电源,数字: 2.7 V ~ 5.25 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 20-SSOP(0.209",5.30mm 宽)
供应商设备封装: 20-SSOP
包装: 带卷 (TR)
3
PIN DESCRIPTIONS
POWER SUPPLY
VDD
Positive Power Supply (Pin 6)
This is the most positive power supply and is typically con-
nected to + 3 V. This pin should be decoupled to VSS with a
0.1
F ceramic capacitor.
VSS
Negative Power Supply (Pin 15)
This is the most negative power supply and is typically
connected to 0 V.
VAG
Analog Ground Output (Pin 20)
This output pin provides a mid–supply analog ground. This
pin should be decoupled to VSS with a 0.01 F ceramic ca-
pacitor. All analog signal processing within this device is ref-
erenced to this pin. If the audio signals to be processed are
referenced to VSS, then special precautions must be utilized
to avoid noise between VSS and the VAG pin. Refer to the ap-
plications information in this document for more information.
The VAG pin becomes high impedance when this device is in
the powered–down mode.
VAG Ref
Analog Ground Reference Bypass (Pin 1)
This pin is used to capacitively bypass the on–chip circuit-
ry that generates the mid–supply voltage for the VAG output
pin. This pin should be bypassed to VSS with a 0.1 F ceram-
ic capacitor using short, low inductance traces. The VAG Ref
pin is only used for generating the reference voltage for the
VAG pin. Nothing is to be connected to this pin in addition to
the bypass capacitor. All analog signal processing within this
device is referenced to the VAG pin. If the audio signals to be
processed are referenced to VSS, then special precautions
must be utilized to avoid noise between VSS and the VAG pin.
Refer to the applications information in this document for
more information. When this device is in the powered–down
mode, the VAG Ref pin is pulled to the VDD power supply with
a non–linear, high–impedance circuit.
CONTROL
Mu/A
Mu/A Law Select (Pin 16)
This pin controls the compression for the encoder and the
expansion for the decoder. Mu–Law companding is selected
when this pin is connected to VDD and A–Law companding is
selected when this pin is connected to VSS.
PDI
Power–Down Input (Pin 10)
This pin puts the device into a low power dissipation mode
when a logic 0 is applied. When this device is powered down,
all of the clocks are gated off and all bias currents are turned
off, which causes RO–, PO–, PO+, TG, VAG, and DT to be-
come high impedance and the VAG Ref pin is pulled to the
VDD power supply with a non–linear, high–impedance circuit.
The device will operate normally when a logic 1 is applied to
this pin. The device goes through a power–up sequence
when this pin is taken to a logic 1 state, which prevents the
DT PCM output from going low impedance for at least two
FST cycles. The VAG and VAG Ref circuits and the signal pro-
cessing filters must settle out before the DT PCM output or
the RO– receive analog output will represent a valid analog
signal.
ANALOG INTERFACE
TI +
Transmit Analog Input (Non–Inverting) (Pin 19)
This is the non–inverting input of the transmit input gain
setting operational amplifier. This pin accommodates a differ-
ential to single–ended circuit for the input gain setting op
amp. This allows input signals that are referenced to the VSS
pin to be level shifted to the VAG pin with minimum noise.
This pin may be connected to the VAG pin for an inverting
amplifier configuration if the input signal is already refer-
enced to the VAG pin. The common mode range of the TI+
and TI– pins is from 1.2 V, to VDD minus 1.2 V. This is an FET
gate input.
The TI+ pin also serves as a digital input control for the
transmit input multiplexer. Connecting the TI+ pin to VDD will
place this amplifier’s output (TG) into a high–impedance
state, and selects the TG pin to serve as a high–impedance
input to the transmit filter. Connecting the TI+ pin to VSS will
also place this amplifier’s output (TG) into a high–impedance
state, and selects the TI– pin to serve as a high–impedance
input to the transmit filter.
TI–
Transmit Analog Input (Inverting) (Pin 18)
This is the inverting input of the transmit gain setting op-
erational amplifier. Gain setting resistors are usually con-
nected from this pin to TG and from this pin to the analog
signal source. The common mode range of the TI+ and TI–
pins is from 1.2 V to VDD – 1.2 V. This is an FET gate input.
The TI– pin also serves as one of the transmit input multi-
plexer pins when the TI+ pin is connected to VSS. When TI+
is connected to VDD, this pin is ignored. See the pin descrip-
tions for the TI+ and the TG pins for more information.
TG
Transmit Gain (Pin 17)
This is the output of the transmit gain setting operational
amplifier and the input to the transmit band–pass filter. This
op amp is capable of driving a 2 k
load. Connecting the TI+
pin to VDD will place the TG pin into a high–impedance state,
and selects the TG pin to serve as a high–impedance input to
the transmit filter. All signals at this pin are referenced to the
VAG pin. When TI+ is connected to VSS, this pin is ignored.
See the pin descriptions for the TI+ and TI– pins for more in-
formation. This pin is high impedance when the device is in
the powered–down mode.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相关PDF资料
PDF描述
MC145483EGR2 IC CODEC-FILTER PCM 3V 20-SOIC
MC145484ENR2 IC CODEC-FILTER PCM 5V 20-SSOP
MC145572AAC IC TRANSCEIVER ISDN 44-LQFP
MC14LC5480ENR2 IC CODEC-FILTER PCM 5V 20-SSOP
MC14LC5540DW IC CODEC ADPCM 28-SOIC W
相关代理商/技术参数
参数描述
MC145481SD 功能描述:IC CODEC-FILTER PCM 3V 20-SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 编解码器 系列:- 标准包装:2,500 系列:- 类型:立体声音频 数据接口:串行 分辨率(位):18 b ADC / DAC 数量:2 / 2 三角积分调变:是 S/N 比,标准 ADC / DAC (db):81.5 / 88 动态范围,标准 ADC / DAC (db):82 / 87.5 电压 - 电源,模拟:2.6 V ~ 3.3 V 电压 - 电源,数字:1.7 V ~ 3.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-WFQFN 裸露焊盘 供应商设备封装:48-TQFN-EP(7x7) 包装:带卷 (TR)
MC145481SDR2 功能描述:IC CODEC-FILTER PCM 3V 20-SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 编解码器 系列:- 标准包装:2,500 系列:- 类型:立体声音频 数据接口:串行 分辨率(位):18 b ADC / DAC 数量:2 / 2 三角积分调变:是 S/N 比,标准 ADC / DAC (db):81.5 / 88 动态范围,标准 ADC / DAC (db):82 / 87.5 电压 - 电源,模拟:2.6 V ~ 3.3 V 电压 - 电源,数字:1.7 V ~ 3.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-WFQFN 裸露焊盘 供应商设备封装:48-TQFN-EP(7x7) 包装:带卷 (TR)
MC145483DT 功能描述:IC PCM COD-FILT 3V 13BIT 20TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 编解码器 系列:- 标准包装:2,500 系列:- 类型:立体声音频 数据接口:串行 分辨率(位):18 b ADC / DAC 数量:2 / 2 三角积分调变:是 S/N 比,标准 ADC / DAC (db):81.5 / 88 动态范围,标准 ADC / DAC (db):82 / 87.5 电压 - 电源,模拟:2.6 V ~ 3.3 V 电压 - 电源,数字:1.7 V ~ 3.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-WFQFN 裸露焊盘 供应商设备封装:48-TQFN-EP(7x7) 包装:带卷 (TR)
MC145483DW 功能描述:IC CODEC-FILTER PCM 3V 20-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 编解码器 系列:- 标准包装:2,500 系列:- 类型:立体声音频 数据接口:串行 分辨率(位):18 b ADC / DAC 数量:2 / 2 三角积分调变:是 S/N 比,标准 ADC / DAC (db):81.5 / 88 动态范围,标准 ADC / DAC (db):82 / 87.5 电压 - 电源,模拟:2.6 V ~ 3.3 V 电压 - 电源,数字:1.7 V ~ 3.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-WFQFN 裸露焊盘 供应商设备封装:48-TQFN-EP(7x7) 包装:带卷 (TR)
MC145483DWR2 功能描述:IC CODEC-FILTER PCM 3V 20-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 编解码器 系列:- 标准包装:2,500 系列:- 类型:立体声音频 数据接口:串行 分辨率(位):18 b ADC / DAC 数量:2 / 2 三角积分调变:是 S/N 比,标准 ADC / DAC (db):81.5 / 88 动态范围,标准 ADC / DAC (db):82 / 87.5 电压 - 电源,模拟:2.6 V ~ 3.3 V 电压 - 电源,数字:1.7 V ~ 3.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-WFQFN 裸露焊盘 供应商设备封装:48-TQFN-EP(7x7) 包装:带卷 (TR)