- 您现在的位置：买卖IC网 > PDF目录378660 > MC1496D (MOTOROLA INC) BALANCED MODULATORS/DEMODULATORS PDF资料下载
参数资料
| 型号： | MC1496D |
| 厂商： | MOTOROLA INC |
| 元件分类： | 消费家电 |
| 英文描述： | BALANCED MODULATORS/DEMODULATORS |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| 封装： | PLASTIC, SOIC-14 |
| 文件页数： | 3/12页 |
| 文件大小： | 310K |
| 代理商： | MC1496D |
MC1496, B
3
MOTOROLA ANALOG IC DEVICE DATA
GENERAL OPERATING INFORMATION
Carrier Feedthrough
Carrier feedthrough is defined as the output voltage at
carrier frequency with only the carrier applied (signal
voltage = 0).
Carrier null is achieved by balancing the currents in the
differential amplifier by means of a bias trim potentiometer
(R1 of Figure 5).
Carrier Suppression
Carrier suppression is defined as the ratio of each
sideband output to carrier output for the carrier and signal
voltage levels specified.
Carrier suppression is very dependent on carrier input
level, as shown in Figure 22. A low value of the carrier does
not fully switch the upper switching devices, and results in
lower signal gain, hence lower carrier suppression. A higher
than optimum carrier level results in unnecessary device and
circuit carrier feedthrough, which again degenerates the
suppression figure. The MC1496 has been characterized
with a 60 mVrms sinewave carrier input signal. This level
provides optimum carrier suppression at carrier frequencies
in the vicinity of 500 kHz, and is generally recommended for
balanced modulator applications.
Carrier feedthrough is independent of signal level, VS.
Thus carrier suppression can be maximized by operating
with large signal levels. However, a linear operating mode
must be maintained in the signal–input transistor pair – or
harmonics of the modulating signal will be generated and
appear in the device output as spurious sidebands of the
suppressed carrier. This requirement places an upper limit on
input–signal amplitude (see Figure 20). Note also that an
optimum carrier level is recommended in Figure 22 for good
carrier suppression and minimum spurious sideband
generation.
At higher frequencies circuit layout is very important in
order to minimize carrier feedthrough. Shielding may be
necessary in order to prevent capacitive coupling between
the carrier input leads and the output leads.
Signal Gain and Maximum Input Level
Signal gain (single–ended) at low frequencies is defined
as the voltage gain,
Vo
VS
A constant dc potential is applied to the carrier input terminals
to fully switch two of the upper transistors “on” and two
transistors “off” (VC = 0.5 Vdc). This in effect forms a cascode
differential amplifier.
Linear operation requires that the signal input be below a
critical value determined by RE and the bias current I5.
VS
I5 RE (Volts peak)
AVS
RL
Re2re
where re
26 mV
I5(mA)
Note that in the test circuit of Figure 10, VS corresponds to a
maximum value of 1.0 V peak.
Common Mode Swing
The common–mode swing is the voltage which may be
applied to both bases of the signal differential amplifier,
without saturating the current sources or without saturating
the differential amplifier itself by swinging it into the upper
switching devices. This swing is variable depending on the
particular circuit and biasing conditions chosen.
Power Dissipation
Power dissipation, PD, within the integrated circuit package
should be calculated as the summation of the voltage–current
products at each port, i.e. assuming V12 = V6, I5 = I6 = I12
and ignoring base current, PD = 2 I5 (V6 – V14) + I5)
V5 – V14 where subscripts refer to pin numbers.
Design Equations
The following is a partial list of design equations needed to
operate the circuit with other supply voltages and input
conditions.
A. Operating Current
The internal bias currents are set by the conditions at Pin 5.
Assume:
I5 = I6 = I12,
IB
IC for all transistors
then :
V
I5
where:
φ
= 0.75 at TA = +25
°
C
The MC1496 has been characterized for the condition
I5 = 1.0 mA and is the generally recommended value.
B. Common–Mode Quiescent Output Voltage
R5
500
where: R5 is the resistor between
where:
Pin 5 and ground
V6 = V12 = V+ – I5 RL
Biasing
The MC1496 requires three dc bias voltage levels which
must be set externally. Guidelines for setting up these three
levels include maintaining at least 2.0 V collector–base bias
on all transistors while not exceeding the voltages given in
the absolute maximum rating table;
30 Vdc
[(V6, V12) – (V8, V10)]
30 Vdc
[(V8, V10) – (V1, V4)]
30 Vdc
[(V1, V4) – (V5)]
The foregoing conditions are based on the following
approximations:
V6 = V12, V8 = V10, V1 = V4
Bias currents flowing into Pins 1, 4, 8 and 10 are transistor
base currents and can normally be neglected if external bias
dividers are designed to carry 1.0 mA or more.
2 Vdc
2.7 Vdc
2.7 Vdc
Transadmittance Bandwidth
Carrier transadmittance bandwidth is the 3.0 dB bandwidth
of the device forward transadmittance as defined by:
io(each sideband)
vs(signal)
Signal transadmittance bandwidth is the 3.0 dB bandwidth
of the device forward transadmittance as defined by:
io(signal)
21C
Vo
0
21S
vs(signal)
Vc
0.5 Vdc, Vo
0
相关PDF资料 |
PDF描述 |
|---|---|
| MC1496P | BALANCED MODULATORS/DEMODULATORS |
| MC14LC5480 | 5 V PCM Codec-Filter |
| MC14LC5480DW | 5 V PCM Codec-Filter |
| MC14LC5480P | Regulating Pulse-Width Modulators 16-PDIP 0 to 70 |
| MC14LC5480SD | Regulating Pulse-Width Modulators 16-PDIP 0 to 70 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC1496DG | 功能描述:调节器/解调器 Balanced Mod/DeMod RoHS:否 制造商:Texas Instruments 封装 / 箱体:PVQFN-N24 封装:Reel |
| MC1496DG | 制造商:ON Semiconductor 功能描述:Modulation / Demondulation IC |
| MC1496DR2 | 功能描述:调节器/解调器 Balanced Mod/DeMod RoHS:否 制造商:Texas Instruments 封装 / 箱体:PVQFN-N24 封装:Reel |
| MC1496DR2G | 功能描述:调节器/解调器 Balanced Mod/DeMod RoHS:否 制造商:Texas Instruments 封装 / 箱体:PVQFN-N24 封装:Reel |
| MC1496DR2G | 制造商:ON Semiconductor 功能描述:Communication IC |
发布紧急采购，3分钟左右您将得到回复。