参数资料
| 型号： | MC33363BDWR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SWIT PWM HV 16SOIC |
| 标准包装： | 1 |
| 输出隔离： | 隔离 |
| 频率范围： | 59kHz ~ 315kHz |
| 输入电压： | 11.5 V ~ 40 V |
| 输出电压： | 700V |
| 工作温度： | -25°C ~ 125°C |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽）13 引线 |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 剪切带 (CT) |
| 其它名称： | MC33363BDWR2GOSCT |
MC33363B
OPERATING DESCRIPTION
Introduction
The MC33363B represents a new higher level of
integration by providing all the active high voltage power,
control, and protection circuitry required for
implementation of a flyback or forward converter on a single
monolithic chip. This device is designed for direct operation
The formula for the charge/discharge current along with
the oscillator frequency are given below. The frequency
formula is a first order approximation and is accurate for C T
values greater than 500 pF. For smaller values of C T , refer
to Figure 2. Note that resistor R T also programs the Current
Limit Comparator threshold.
= R
T
from a rectified 240 Vac line source and requires a minimum
number of external components to implement a complete
converter. A description of each of the functional blocks is
I
chg ∕ dscg
5.4
T
f ≈
I
chg ∕ dscg
4C
given below, and the representative block and timing
diagrams are shown in Figures 19, 18 and 20.
Oscillator and Current Mirror
The oscillator frequency is controlled by the values
selected for the timing components R T and C T . Resistor R T
programs the oscillator charge/discharge current via the
Current Mirror 4 I output, Figure 4. Capacitor C T is charged
and discharged by an equal magnitude internal current
source and sink. This generates a symmetrical 50 percent
duty cycle waveform at Pin 7, with a peak and valley
threshold of 2.6 V and 0.6 V respectively. During the
discharge of C T , the oscillator generates an internal blanking
pulse that holds the inverting input of the AND gate Driver
high. This causes the Power Switch gate drive to be held in
a low state, thus producing a well controlled amount of
output deadtime. The amount of deadtime is relatively
constant with respect to the oscillator frequency when
operating below 1.0 MHz. The maximum Power Switch
duty cycle at Pin 16 can be modified from the internal 50%
limit by providing an additional charge or discharge current
path to C T , Figure 21. In order to increase the maximum duty
cycle, a discharge current resistor R D is connected from
Pin 7 to ground. To decrease the maximum duty cycle, a
charge current resistor R C is connected from Pin 7 to the
Regulator Output. Figure 5 shows an obtainable range of
maximum output duty cycle versus the ratio of either R C or
R D with respect to R T .
PWM Comparator and Latch
The pulse width modulator consists of a comparator with
the oscillator ramp voltage applied to the non--inverting input,
while the error amplifier output is applied into the inverting
input. The Oscillator applies a set pulse to the PWM Latch
while C T is discharging, and upon reaching the valley voltage,
Power Switch conduction is initiated. When C T charges to a
voltage that exceeds the error amplifier output, the PWM
Latch is reset, thus terminating Power Switch conduction for
the duration of the oscillator ramp--up period. This
PWM Comparator/Latch combination prevents multiple
output pulses during a given oscillator clock cycle. The
timing diagram shown in Figure 18 illustrates the Power
Switch duty cycle behavior versus the Compensation voltage.
Current Limit Comparator and Power Switch
The MC33363B uses cycle--by--cycle current limiting as a
means of protecting the output switch transistor from
overstress. Each on--cycle is treated as a separate situation.
Current limiting is implemented by monitoring the output
switch current buildup during conduction, and upon sensing
an overcurrent condition, immediately turning off the switch
for the duration of the oscillator ramp--up period.
The Power Switch is constructed as a SENSEFET allowing
a virtually lossless method of monitoring the drain current. It
consists of a total of 1462 cells, of which 36 are connected to
a 8.1 Ω ground--referenced sense resistor. The Current Sense
Comparator detects if the voltage across the sense resistor
Regulator Output
1.0 8
Current
Mirror
2.25 I
exceeds the reference level that is present at the inverting
input. If exceeded, the comparator quickly resets the PWM
Latch, thus protecting the Power Switch. The current limit
reference level is generated by the 2.25 I output of the Current
RC
RD
R T
C T
6
7
I
4I
Oscillator
Current
Limit
Reference
Blanking
Pulse
Mirror. This current causes a reference voltage to appear
across the 405 Ω resistor. This voltage level, as well as the
Oscillator charge/discharge current are both set by resistor R T .
Therefore when selecting the values for R T and C T , R T must
be chosen first to set the Power Switch peak drain current,
while C T is chosen second to set the desired Oscillator
frequency. A graph of the Power Switch peak drain current
versus R T is shown in Figure 3 with the related formula
below.
? ?
PWM
Comparator
Figure 21. Maximum Duty Cycle Modification
I
pk
= 8.8
RT --
1000 1.077
http://onsemi.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| MC33364D2G | IC CTRLR SMPS OTP UVLO 8SOIC |
| MC33385DHR2 | IC SWITCH QUAD L-SIDE 20-HSOP |
| MC33470DWR2G | IC CONV DC/DC SYNC RECT 20-SOIC |
| MC33580BAPNAR2 | IC SW QUAD HI SIDE 15MOHM 24PQFN |
| MC33761SNT1-050G | IC REG LDO 5V 80MA 5TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33363P | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC33364D | 功能描述:电流型 PWM 控制器 Variable Frequency RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MC33364D1 | 功能描述:电流型 PWM 控制器 Variable Frequency RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MC33364D1G | 功能描述:电流型 PWM 控制器 Variable Frequency SMPS RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MC33364D1R2 | 功能描述:电流型 PWM 控制器 Variable Frequency RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。