- 您现在的位置：买卖IC网 > PDF目录359132 > MC33388 (飞思卡尔半导体(中国)有限公司) Fault Tolerant CAN Interface(容错CAN接口) PDF资料下载
参数资料
| 型号： | MC33388 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 英文描述： | Fault Tolerant CAN Interface(容错CAN接口) |
| 中文描述： | 容错CAN接口（容错的CAN接口） |
| 文件页数： | 8/28页 |
| 文件大小： | 583K |
| 代理商： | MC33388 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
MC33388
8
MC33388
Battery Fail Flag
When the VBAT supply drops below “battery voltage for
setting power on flag” threshold, this information is internally
latched. This means that the system power supply has been
lost (disconnected and reconnected for instance).
This flag can be read by the microcontroller by switching
the device into receive only mode, where NERR pin reports
the VBAT power on flag. This flag is reset by entering into the
Normal mode.
Bus Failure Detection
The device permanently monitors the bus lines and
detects faults in normal and receive only modes. Below is the
list of failures detected at the bus level :
1- CANH wire interruption
2- CANL wire interruption
3- CANH short-circuit to battery
4- CANL short-circuit to ground
5- CANH short-circuit to ground
6- CANL short-circuit to battery
7- CANL and CAN H mutually shorted
8- CANH short-circuit to Vdd
TX Permanent Dominant Detection
In addition to the above list, the MC33388 detects a
permanent low state at TX input which results of a permanent
dominant bus state. The MC33388 detects if TX is Low for
more than 2ms typical and then disables the bus output driver
in order to switch into recessive state. This avoid to block
communication between other nodes of the network.
Behaviour Under Faults Condition
When a fault is detected, the device automatically takes
appropriate action to minimize the system current
consumption and to allow communication on the network.
Depending on the type of fault, the mode of operation and the
fault detected, the device automatically switches off one or
more of the following functions: CANL or CANH line driver, Rtl
or Rth pull up or down resistors or internal switches. These
actions are detailed in table 2.
The device permanently monitors the faults and in case of
fault recovery, it automatically switches back to normal
operation and reconnects the open functions. Faults detection
and recovery circuitry have internal filters and delays timing
detailed in the AC characteristics parameters section.
Detailed Description of Error Detections
The differential receiver threshold is set at -2,8V. This
assures a proper reception in the normal operating modes
and in case of failures 1, 2 and 5 noise margin as high as
possible. These failures or their recovery do not destroy
ongoing transmissions.
Failures 3 and 6 are detected by comparators respectively
connected to CANH and CANL. If the comparator threshold is
exceeded for a certain time, the device is switched to single
wire mode. This time is needed to avoid false triggering by
external RF fields. Recovery from these failures is detected
automatically after a certain time-out (filtering) and no
transmission is lost.
Failures 4, 7 and 8 initially result in a permanent dominant
level at the internal comparator outputs. If failure 4 and 7
appear, the CANL driver and the RTL pin are switched off
after a time out, only a weak pull up at RTL remains.
Reception continues by switching to single wire mode through
CANH. When the failures 4 or 7 are removed, the recessive
bus levels are restored. If the receiver voltages remain in the
recessive state for a certain time, reception and transmission
switch back to the differential mode.
If failure 8 is recognized, the CANH driver is switched off
after a time out and the reception is switched to single wire
mode through CANL. If the receiver voltages remain in the
recessive state for a certain time, reception and transmission
switch back automatically to the differential mode.
If any of the 8 wiring failure occurs, the output NERR will
be switched low. When the error recovers, NERR will be
switched back to high state.
Wake Up Events
Wake-up requests are recognized by the MC33388 in
Sleep or VBAT Stanby modes, either when a dominant state
is detected on CANL or CANH bus lines (remote wake-up) or
if the WAKE pin changes state (local wake-up).
Under power-up conditions when VBAT is higher than 5V,
the state voltage on the WAKE pin is considered to be the
reference state for the wake-up function. On leaving normal
mode, the current WAKE pin state becomes the new
reference state.
In sleep mode, on a wake-up request the transceiver sets
the INH output high, to activate the external voltage regulator,
used for VDD supplied. In VBAT standby INH is already set
high. When VDD is set, the wake-up request can be read on
the NERR or RX outputs by the microcontroller.
To prevent false wake-up due to transients or RF fields,
wake-up threshold levels have to be maintained for a certain
time. In the low power modes, failure detection circuit remains
partly active to prevent increased power consumption in
cases of error 3, 4, 7 and 8.
Fault Operation Table
Table 2 shows the device operation in normal and low
power modes and the internal actions happening under fault
condition. Please refer to simplified block diagram page 1 for
device internal switch reference.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33389 | System Basis Chip with Low Speed Fault Tolerant CAN(带低速容错CAN接口的系统基片) |
| MC33390 | J-1850 SERIAL TRANSCEIVER(串行J-1850总线收发器) |
| MC33394 | Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(带有多个线性稳压器和高速CAN收发器的开关方式电源) |
| MC33395 | Three-Phase Gate Driver IC(3相栅极驱动器) |
| MC33397 | Dual/Hex Low-Side Switch with Both SPI and Parallel Input Control(带SPI和并口输入控制的2或6低端开关) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33388D | 功能描述:IC CAN FAULT TOL INTRFACE 14SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| MC33388DR2 | 功能描述:IC TOLERANT CAN INT FAULT 14SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| MC33389CDH | 功能描述:IC SYSTEM BASIS W/CAN 20-HSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| MC33389CDHR2 | 功能描述:IC SYSTEM BASE W/CAN 20-HSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| MC33389CDW | 功能描述:网络控制器与处理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。