- 您现在的位置：买卖IC网 > PDF目录11546 > MC33389CDWR2 (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28-SOIC PDF资料下载
参数资料
| 型号： | MC33389CDWR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 22/49页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28-SOIC |
| 标准包装： | 1 |
| 控制器类型： | 系统基础芯片 |
| 接口： | CAN |
| 电源电压： | 5.5 V ~ 18 V |
| 电流 - 电源： | 45mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 剪切带 (CT) |
| 其它名称： | MC33389CDWR2CT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
33389
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Sleep Mode Activation
Once in the Sleep mode, the SBC turns the V1 and V2
regulator OFF . Thus the microcontroller can not run any
mode.
In order to have the microcontroller run again, the SBC
should enable and turn ON V1. This is achieved by an SBC
wake-up event.
Several options are available to wake-up the SBC and the
application and have the microcontroller in Run mode.
Some wake-ups are selectable; some are always active in
Sleep mode:
Wake-up from CAN interface and wake-up from SPI (CS)
are always active.
Wake-up from L0,L1, and L2 inputs, with and without cyclic
sense and the forced wake-up (FWU) are selectable. The
selection must be done while the SBC is in Normal or
Stand-by mode, and prior to enter Sleep mode.
General Condition to Enter Sleep Mode
All previous wake-up conditions must be cleared, assuring
the SBC enters the Sleep mode, and Write operations into
the MCR and MCVR. To clear a wake-up condition requires
reading the appropriate register.
Once the SBC has powered-up from zero (battery power-
up or cold start), the following registers must be read:
WUICR—possible wake-up event report from CAN bus
RSR—report a V1 under voltage
VSSR—reports a VBAT fail flag
Once these read operations are completed, the wake-up
conditions, or flags are reset.
The VBSR0 bit in the VSSR can be used to determine if
the SBC has experienced a loss of battery voltage.
Once the SBC is awakened from Sleep mode the following
registers indicate the wake-up source. They must be cleared
to allow the SBC to enter Sleep mode again:
WUICR—wake-up event report for CAN or SPI buses
WUISR— wake-up event report for the L0,L1, and L2
inputs
RSR—report a V1 under voltage
VSSR—reports a VBAT fail flag
etc.
The ensuing paragraphs describe the write operation to be
accomplished for the several Sleep modes and Wake-up
control options.
In addition to FWU, cyclic sense and direct wake-up, the
CAN and SPI wake will always be activated.
Sleep Mode with CAN and SPI Wake-Up
To enter the Sleep mode and activate the only CAN or SPI
wake-up, there is no dedicated wake-up condition to be
completed. The SBC has CAN and SPI wake-up sources
always active in the Sleep mode. To enter the Sleep mode in
this case, while the SBC is in Normal or Stand-by mode:
Write to V3R—data 0000 (this clears the WI2V3 bit, is set
to1after reset)
Write to MCR—data SLEEP (100)
Write to MCVR—data SLEEP (100)
The SBC then enters the Sleep mode.
Sleep Mode Enter with Forced Wake-Up
To enter the Sleep mode and activate the forced wake-up,
write to the following registers:
Write to V3R (data 0100) this set the FWU bit to 1
Write the desired wake-up time to CYTCR. (This sets the
time the SBC will stay in the Sleep mode).
Write to MCR–data SLEEP (100)
Write to MCVR– data SLEEP (100)
The SBC then enters the Sleep mode. It will wake-up after
the time period is selected in the CYTCR.
Sleep Mode Enter with Cyclic Sense
To enter the Sleep mode and activate the cyclic sense
wake-up the following registers must be written:
Write to V3R (data 1010) this sets the VI2V3 and CYS bits
to 1
Write to CYTCR the desired cyclic sense period. (This sets
the time the SBC will wait in the Sleep mode to turn on V3
and sense the LX inputs)
Write to WUICR bits 0 and 1 to select the edge sensitivity
for the LX inputs
Write to MCR—data SLEEP (100)
Write to MCVR—data SLEEP (100)
The SBC then enters the Sleep mode. It will periodically
turn on V3 and while V3 is on, sample the level of the Ls
inputs.
If any of the 3 LX inputs is in the correct state for two
consecutive samples, SBC will wake-up. If not, it will stay in
the Sleep mode. Refer to device description for detail.
Sleep Mode Enter With Direct LX Input Wake-Up
To enter the Sleep mode and activate the direct wake-up
from the LX inputs, the following registers must be written:
Write to V3R (data 0000) this clear VI2V3 bit
Write to WUICR bits 0 and 1 to select the edge sensitivity
for the LX inputs
Write to MCR—data SLEEP (100)
Write to MCVR—data SLEEP (100)
The SBC then enters the Sleep mode. It will wake-up as
soon as any of the LX input read the correct state.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33389CDH | IC SYSTEM BASIS W/CAN 20-HSOP |
| MC33989DW | IC SYSTEM BASE W/CAN 28-SOIC |
| MC33889DW | IC SYSTEM BASE W/CAN 28-SOIC |
| MC33389CDW | IC SYSTEM BASE W/CAN 28-SOIC |
| MC33388DR2 | IC TOLERANT CAN INT FAULT 14SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33389DDW | 功能描述:网络控制器与处理器 IC SBC SOW28 RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33389DDWR2 | 功能描述:网络控制器与处理器 IC SBC SOW28 RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33390D | 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC33390DR2 | 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC33390EF | 制造商:Freescale Semiconductor 功能描述: |
发布紧急采购，3分钟左右您将得到回复。