参数资料
型号: MC33591MOD315EV
厂商: Freescale Semiconductor
文件页数: 16/28页
文件大小: 0K
描述: BOARD EVAL MC33493 TANGO3 RF
标准包装: 1
类型: 接收器,UHF
频率: 315MHz
适用于相关产品: MC33591
已供物品:
Freescale Semiconductor, Inc.
STROBE OSCILLATOR
Programming SOE=0 sets ROMEO2 to state 6. The circuit is in Sleep mode.
State 7:
A high level applied on STROBE sets the circuit into state 7. If an ID or its complement is detected, the state
machine advances to state 8. If not, it will stay in state 7 as long as STROBE is high.
State 8:
After ID or its complement detection, ID byte is sent to the microcontroller on MOSI line at 310kBd. This warns
the microcontroller that data are received which means that an high level has to be maintained on STROBE. At
any time a low level applied on STROBE sets the circuit into state 6.
State 9:
If Header or its complement is detected, the state machine advances to state 10. If not, it will stay in state 9 as
long as STROBE is high.
State 10:
If Header has been received, data and clock signals are output on the SPI port. If the complement of Header has
been received, output data are complemented too. At any time a low level applied on STROBE sets the circuit
into state 6, after the current byte is fully transmitted.
State 11:
If data are received after a End of Message they are output on the MOSI pin without clock recovery.
For all states:
At any time, a low level applied on RESETB for more than one Ts forces the state machine to state 1. When the
transition condition from one state to the next one is fulfilled, the transition time is one Ts except reaching state 6.
The transition time for reaching state 6 is 2 ′ Ts (+ time needed to shift out a full byte if STROBE pin is forced to
low when in state 10).
STROBE OSCILLATOR
The Strobe Oscillator is a relaxation oscillator in which an external capacitor C5 is charged by an external
resistance R2 (refer to figure 17 and table 11). When a threshold is reached or exceeded C5 is discharged and
the cycle restarts. The period is: T Strobe =0.12 ′ R2 ′ C5.
The circuit may be forced into states 0b, 3, 7 etc. (see State Machine Diagrams) by setting the STROBE pin to
V CC . As V CC is above the oscillator threshold voltage referred to in the previous paragraph, the condition in which
the STROBE pin is set to V CC is internally detected and the oscillator pull-down circuitry disabled to limit the
current which must be supplied.
16
MC33591 Technical Data
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
相关PDF资料
PDF描述
MC33593MOD868EV BOARD EVAL MC33593 ROMEO2 RF
MC33690DWER2 IC STAND ALONE TAG READER 20SOIC
MC44CC375AVEFEVK CCEVK NEJA EVAL KIT
MCH3374-TL-E MOSFET P-CH 12V 3A MCPH3
MCH3375-TL-H MOSFET P-CH 1.6A 30V MCPH3
相关代理商/技术参数
参数描述
MC33591MOD434 功能描述:BOARD EVALUATION FOR MC33591 RX RoHS:否 类别:RF/IF 和 RFID >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:用于 200/300 系列的欧盟开发套件 适用于相关产品:Zensys RF 模块 所含物品:开发板,模块,编程器,软件,线缆,电源 其它名称:703-1019Q3225667
MC33591MOD434EV 功能描述:开发板和工具包 - 无线 MC33591 (ROMEO2) RF EVAL RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:AT32UC3L 核心:AVR32 频率: 接口类型:USB 工作电源电压:5 V
MC33592FTA 功能描述:IC RF RECEIVER 315,434MHZ 24LQFP RoHS:否 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB,表面贴装 存储容量:- 天线连接器:PCB,表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP(6x6) 包装:托盘
MC33592FTAE 功能描述:射频接收器 UHF RECEIVER RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MC33592FTAER2 功能描述:射频接收器 UHF RECEIVER RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel