- 您现在的位置：买卖IC网 > PDF目录11717 > MC33742DW (Freescale Semiconductor)IC SYSTEM BASE W/LIN 28-SOIC PDF资料下载
参数资料
| 型号： | MC33742DW |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 15/71页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASE W/LIN 28-SOIC |
| 标准包装： | 26 |
| 应用： | 自动 |
| 接口： | SPI |
| 电源电压： | 5.5 V ~ 18 V |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
| 配用： | KIT33742DWEVB-ND - KIT FOR 33742 SBC WITH EHSCAN |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
Analog Integrated Circuit Device Data
22
Freescale Semiconductor
33742
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 33742 and the 33742S are system basis chips (SBCs) dedicated to automotive applications. Their functions include the
following:
One fully protected 5.0 V voltage regulator with 200 mA total output current capability available at the VDD pin.
VDD regulator under-voltage reset function, programmable window or time-out software watchdog function.
Internal driver (V2) for an external series pass transistor to implement a second 5.0 V voltage regulator.
Two running modes: Normal and Standby modes set by the system microcontroller.
Sleep and Stop modes low power operating modes to reduce an application’s current consumption while providing a wake-
up capability from the CAN interface, L3:L0 wake-up inputs, or from a timer wake-up.
Programmable wake-up input and cyclic sense wake-ups.
CAN high-speed physical bus interface with TXD and RXD fault diagnostic capability and enhanced protection features.
An SPI interface for use in communicating with a MCU and Interrupt outputs to report SBC status, perform diagnostics, and
report wake-up events.
FUNCTIONAL PIN DESCRIPTION
RECEIVE AND TRANSMIT DATA (RXD AND TXD)
The RXD and TXD pins (receive data and transmit data pins, respectively) are connected to a microcontroller’s CAN protocol
handler. TXD is an input and controls the CANH and CANL line state (dominant when TXD is LOW, recessive when TXD is
HIGH). RXD is an output and reports the bus state (RXD LOW when CAN bus is dominant, HIGH when CAN bus is recessive).
The RXD terminal is a push-pull structure between the V2 pin and GND.
Voltage Digital Drain (VDD)
The VDD pin is the output pin of the 5.0 V internal regulator. It can deliver up to 200 mA. This output is protected against over-
current and over-temperature. It includes an over-temperature pre-warning flag, which is set when the internal regulator
temperature exceeds 130 °C typical. When the temperature exceeds the over-temperature shutdown (170 °C typical), the
regulator is turned off.
VDD includes an under-voltage reset circuitry, which sets the RST pin LOW when VDD is below the under-voltage reset
threshold.
RESET OUTPUT (RST)
The RESET pin RST, is an output that is set LOW when the device is in reset mode. The RST pin is set HIGH when the device
is not in reset mode. RST includes an internal pull-up current source. When RST is LOW, the sink current capability is limited,
allowing RST to be shorted to 5.0 V for software debug or software download purposes.
INTERRUPT OUTPUT (INT)
The Interrupt pin INT, is an output that is set LOW when an interrupt occurs. INT is enabled using the Interrupt Register (INTR).
When an interrupt occurs, INT stays LOW until the interrupt source is cleared.
INT output also reports a wake-up event by a 10
s typical pulse when the device is in Stop mode.
VOLTAGE SOURCE 2 (V2)
The V2 pin is the input sense for the V2 regulator. It is connected to the external series pass transistor. V2 is also the 5.0 V
supply of the internal CAN interface. It is possible to connect V2 to an external 5.0 V regulator or to the VDD output when no
external series pass transistor is used. In this case, the V2CTRL pin must be left open. Refer to Figure 31, SBC Typical
VOLTAGE SOURCE 2 CONTROL (V2CTRL)
The V2CTRL pin is the output drive pin for the V2 regulator connected to the external series pass transistor.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33742DWR2 | IC SYSTEM BASE W/LIN 28-SOIC |
| D38999/26KA98PN | CONN PLUG 3POS STRAIGHT W/PINS |
| C8051T602-GS | IC 8051 MCU 4K-EEPROM 14-SOIC |
| MS27484T18A35S | CONN PLUG 66POS STRAIGHT W/SCKT |
| MC33689DWB | IC SYSTEM BASE W/LIN 32-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33742DWR2 | 功能描述:网络控制器与处理器 IC SBC-E-HS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33742EP | 功能描述:CAN 接口集成电路 SBC_ECAN_HS RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33742EPR2 | 功能描述:CAN 接口集成电路 SBC_ECAN_HS RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33742PEG | 功能描述:CAN 接口集成电路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33742PEGR2 | 功能描述:CAN 接口集成电路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。