- 您现在的位置：买卖IC网 > PDF目录16409 > MC33886VW (Freescale Semiconductor)IC H-BRIDGE 5.0A OUTPUT 20-HSOP PDF资料下载
参数资料
| 型号： | MC33886VW |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 18/28页 |
| 文件大小： | 0K |
| 描述： | IC H-BRIDGE 5.0A OUTPUT 20-HSOP |
| 标准包装： | 30 |
| 应用： | DC 电机控制器，H 桥式 |
| 评估套件： | 可供 |
| 输出数： | 1 |
| 电流 - 输出： | 5A |
| 电源电压： | 5 V ~ 40 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.433"，11.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 20-HSOP |
| 包装： | 管件 |
| 产品目录页面： | 808 (CN2011-ZH PDF) |
| 配用： | KIT33886DHEVB-ND - KIT EVAL FOR MC33886 H-BRIDGE |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
FUNCTIONAL DEVICE OPERATION
FUNCTIONAL PIN DESCRIPTION
FUNCTIONAL DEVICE OPERATION
SHORT-CIRCUIT PROTECTION
If an output short-circuit condition is detected, the power
outputs tri-state (latch-OFF) independent of the input (IN1
and IN2) states, and the fault status output flag is set logic
Low. If the D1 input changes from logic High to logic Low, or
if the D2 input changes from logic Low to logic High, the
output bridge will become operational again and the fault
status flag will be reset (cleared) to a logic High state.
The output stage will always switch into the mode defined by
the input pins (IN1, IN2, D1, and D2), provided the device
junction temperature is within the specified operating
temperature.
ACTIVE CURRENT LIMITING
The maximum current flow under normal operating
conditions is internally limited to I LIM (5.2 A to 7.8 A). When
the maximum current value is reached, the output stages are
tri-stated for a fixed time (t a ) of 20 ? s typical. Depending on
the time constant associated with the load characteristics, the
current decreases during the tri-state duration until the next
output ON cycle occurs (see Figures 9 and 12 , page 10 and
The current limiting threshold value is dependent upon the
device junction temperature. When -40 ? C < T J < 160 ? C, I LIM
is between 5.2 A and 7.8 A. When T J exceeds 160 ? C, the
I LIM current decreases linearly down to 2.5 A typical at
175 ? C. Above 175 ? C the device overtemperature circuit
detects T LIM and overtemperature shutdown occurs (see
operational for a longer time but at a regressing output
performance level at junction temperatures above 160 ? C.
OVERTEMPERATURE SHUTDOWN AND
HYSTERESIS
If an overtemperature condition occurs, the power outputs
are tri-state (latched-OFF) independent of the input signals
and the fault status flag is set logic Low.
To reset from this condition, D1 must change from logic High
to logic Low, or D2 must change from logic Low to logic High.
When reset, the output stage switches ON again, provided
that the junction temperature is now below the
overtemperature threshold limit minus the hysteresis.
Note Resetting from the fault condition will clear the fault
status flag.
MAIN DIFFERENCES COMPARED TO
MC33186DH1
? COD pin has been removed. Pin 8 is now a Do Not
Connect (DNC) pin.
? Pin 20 is no longer connected in the 20 HSOP package. It
is now a DNC pin.
? R DS(ON) max at T J = 150 °C is now 225 m ? per each
output transistor.
? Maximum temperature operation is now 160 °C, as
minimum thermal shutdown temperature has increased.
? Current regulation limiting foldback is implemented above
160 °C T J .
? Thermal resistance junction to case has been increased
from ~2.0 °C/W to ~5.0 °C/W.
33886
Analog Integrated Circuit Device Data ?
18
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| M3TTK-2018R | IDC CABLE - MSD20K/MC20M/MSD20K |
| SP1008R-223K | INDUCTOR PWR SHIELDED 22.0UH SMD |
| M3DDA-5036J | IDC CABLE - MKR50A/MC50G/MKR50A |
| A3CCB-3036M | IDC CABLE- AKC30B/AE30M/AKC30B |
| A3BKB-1036M | IDC CABLE- ASR10B/AE10M/APK10B |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33886VWR2 | 功能描述:马达/运动/点火控制器和驱动器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33887APVW | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE W/LD CURNT FDBK RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33887APVW-PB | 制造商:Freescale Semiconductor 功能描述: |
| MC33887APVWR2 | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE W/LD CURNT FDBK RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33887AVW | 功能描述:开关 IC - 各种 H-BRIDGE W/LD CURNT FDBK RoHS:否 制造商:Fairchild Semiconductor 开启电阻（最大值）: 电源电压-最大:4.4 V 电源电压-最小:2.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WLCSP-9 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。