- 您现在的位置：买卖IC网 > PDF目录359133 > MC33889 (飞思卡尔半导体(中国)有限公司) System Basis Chip (SBC) with Low Speed Fault Tolerant CAN Interface PDF资料下载
参数资料
| 型号： | MC33889 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | System Basis Chip (SBC) with Low Speed Fault Tolerant CAN Interface |
| 中文描述： | 带有低速CAN的精简版系统基础芯片 |
| 文件页数： | 14/30页 |
| 文件大小： | 464K |
| 代理商： | MC33889 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
PC33889
14
PC33889
4.9.1
Wake up from wake up inputs (L0, L1) without cyclic sense:
The wake up lines are dedicated to sense external switches state and if changes occur to wake up the MCU (In sleep or stop
modes). The wake up pins are able to handle 40V DC. The internal threshold is 3V typical and these inputs can be used as input
port expander. The wake up inputs state can be read through SPI (register WUR). L0 has a lower threshold than L1 in order to
allow connection and wake up from a digital output such as a CAN physical interface for instance.
4.9.2
Cyclic sense wake up (Cyclic sense timer and wake up inputs L0, L1)
The SBC can wake up upon state change of one of the wake up input lines (L0, L1) while the external pull up or pull down
resistor of the switches associated to the wake up input lines are biased with HS1 Vsup switch. The HS1 switch is activated in
sleep or stop mode from an internal timer. Cyclic sense and Forced wake up are exclusive. If Cyclic Sense is enabled the forced
wake up can not be enabled.
4.9.3
Forced wake up
The SBC can wake up automatically after a pre determined time spent in sleep or stop mode. Forced wake up is enabled by
setting bit FWU in LPC register. Cyclic sense and Forced wake up are exclusive. If Forced wake up is enabled the Cyclic Sense
can not be enabled.
4.9.4
CAN wake up
The device can wake up from a CAN message. CAN wake up cannot be disabled.
4.9.5
SPI wake up
The device can wake up by the CSB pin in sleep or stop mode. Wake up is detected by CSB pin transition from low to high
level. In stop mode this correspond to the condition where MCU and SBC are both in Stop mode and when the application wake
up events come through the MCU.
4.9.6
System power up
At power up the device automatically wakes up.
4.10
SPI
The complete device control as well as the status report is done through a 8 bits SPI interface. Refer to SPI paragraph.
4.11
CAN
The device incorporates a low speed fault tolerant CAN physical interface. Speed rate is up to 125kBauds. Its electrical
parameters for the CANL, CANH, Rtl, Rth Rx and Tx pins are compatible with the MC33388D.
The state of the CAN interface is programmable through SPI.
4.12
Device power up, SBC wake up
After device or system power up or a wake up from sleep mode, the SBC enters into “reset mode” then into “normal request
mode”.
4.13
Battery fall early warning:
This function provides an Interrupt when the Vsup voltage is below 6.1V typical. This interrupt is maskable. An hysteresis is
included. Operation is only in Normal and Standby modes. Vbat low state reported in IOR register.
4.14
Package and thermal consideration
The device is proposed in a standard surface mount SO28 package. In order to improve the thermal performances of the
SO28 package, 8 pins are internally connected to the lead frame and are used for heat transfer to the printed circuit board.
4.15
Table 1: Reset and Wdogb operation
Figure below shows the reset and watchdog output operation. Reset is active at device power up and wake up. Reset is
activated in case of Vdd1 fall or watchdog not triggered. Wdogb output is active low as soon as reset goes low and stays low as
long as the watchdog is not properly re-activated by SPI.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33897 | Single-Wire CAN Transceiver(单线CAN收发器) |
| MC33972 | Multiple Switch Detection Interface with Suppressed Wake-Up(带抑制唤醒功能的多开关检测接口) |
| MC33976 | Dual Gauge Driver with Configurable Response Time(带可设置响应时间的双标尺驱动器) |
| MC33984 | Dual Intelligent High-Current Self-Protected Silicon High-Side Switch (4.0 mOhm)(双智能大电流带自保护功能的硅高端开关（4mOhm）) |
| MC33989 | System Basis Chip with High Speed CAN Transceiver(带高速CAN收发器的系统基片) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33889BDW | 功能描述:网络控制器与处理器 IC SBC LIGHT PASS 3.3 RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33889BDWR2 | 功能描述:网络控制器与处理器 IC SBC LIGHT PASS 3.3 RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33889BPEG | 制造商:Freescale Semiconductor 功能描述:SYSTEM BASIS CHIP WITH LOW SPEED FAULT TOLERANT CAN INTERFACE 制造商:Freescale Semiconductor 功能描述:SBC-LITE-LS-CAN - Bulk 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN 28SOIC |
| MC33889BPEGR2 | 制造商:Freescale Semiconductor 功能描述:CAN 125Kbps Sleep/Stop 9V/12V/15V T/R 制造商:Freescale Semiconductor 功能描述:SBC-LITE-LS-CAN - Tape and Reel 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN 28SOIC |
| MC33889DDW | 功能描述:网络控制器与处理器 IC SBC LIGHT REV D RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。