- 您现在的位置：买卖IC网 > PDF目录1948 > MC33989DWR2 (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28-SOIC PDF资料下载
参数资料
| 型号： | MC33989DWR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 15/72页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28-SOIC |
| 标准包装： | 1 |
| 控制器类型： | 系统基础芯片 |
| 接口： | CAN |
| 电源电压： | 5.5 V ~ 18 V |
| 电流 - 电源： | 45mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 剪切带 (CT) |
| 配用： | KIT33989DWEVB-ND - KIT EVAL 33989DW HS SBC |
| 其它名称： | MC33989DWR2CT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
Analog Integrated Circuit Device Data
22
Freescale Semiconductor
33989
FUNCTIONAL DEVICE OPERATION
RESET AND WATCHDOG PINS, SOFTWARE WATCHDOG OPERATIONS
APPLICATION WAKE-UP FROM MCU SIDE
When application is in Stop mode, the wake-up event may come from the MCU side. In this case the MCU signals to the SBC
by a low to high transition on the CS pin. Then the SBC goes into Normal Request mode and generates an interrupt pulse at the
INT pin.
STOP MODE CURRENT MONITOR
If the VDD1 output current exceed an internal threshold (IDD1SWU), the SBC goes automatically into Normal Request mode and
generates an interrupt at the INT pin. The interrupt is not maskable and the interrupt register will has no flag set.
INTERRUPT GENERATION WHEN WAKE-UP FROM STOP MODE
When the SBC wakes up from Stop mode, it first enters the Normal Request mode before generating a pulse (10 s typical)
on the INT pin. These interrupts are not maskable, and the wake-up event can be read through the SPI registers (CANWU bit in
Reset Control Register (RCR) and LCTRx bit in Wake-up Register (WUR). In case of wake-up from Stop mode over current or
from forced wake-up, no bit is set. After the INT pulse the SBC accept SPI command after a time delay (tS1STSPI parameter).
SOFTWARE WATCHDOG IN STOP MODE
If Watchdog is enabled, the MCU has to wake-up independently of the SBC before the end of the SBC watchdog time. In order
to do this, the MCU must signal the wake-up to the SBC through the SPI wake-up (CS activation). The SBC then wakes up and
jumps into the Normal Request mode. MCU has to configured the SBC to go to either Normal or Standby mode. The MCU can
then decide to go back again to Stop mode.
When there is no MCU wake-up occurring within the watchdog timing, the SBC activates the Reset pin, jumping into the
Normal Request mode. The MCU can then be initialized.
STOP MODE ENTER COMMAND
Stop mode is entered at the end of the SPI message, and at the rising edge of the CS. Please refer to the t CSSTOP data in the
Once Stop mode is entered the SBC could wake-up from the V1 regulator overcurrent detection. In order to allow time for the
MCU to complete the last CPU instruction, allowing the MCU to enter its low power mode, a deglitcher time of typical 40 s is
implemented.
Figure 9 indicates the operation to enter Stop mode.
Figure 9. Operation Entering Stop Mode
RESET AND WATCHDOG PINS, SOFTWARE WATCHDOG OPERATIONS
SOFTWARE WATCHDOG (SELECTABLE WINDOW OR TIMEOUT WATCHDOG)
Software watchdog uses in the SBC Normal and Standby modes is to monitor MCU. The Watchdog can be either window or
timeout. This is selectable by SPI (register TIM1, bit WDW). Default is window watchdog. The period for the watchdog is
selectable from the SPI from 10 ms to 350 ms (register TIM1, bits WDT0 and WDT1). When the window watchdog is selected,
the closed window is the first part of the selected period, and the open window is the second part of the period. Refer to the SPI
SPI CS
SPI Stop/ Sleep Command
SBC in Normal or Stand-by mode
SBC in Stop mode
IDD1DGLT
tCSSTOP
with IDD1over I wake-up
no IDD1 over I wake-up
相关PDF资料 |
PDF描述 |
|---|---|
| MC3488ADR2G | IC LINE DRIVER DUAL EIA 8-SOIC |
| MC34940EGR2 | IC IMAGING DEVICE ELEC 24-SOICW |
| MC44BS373CAFCR2 | IC MODULATOR AUD/VID U/V 20-QFN |
| MC44BS374CAEFR2 | IC AUDIO/VIDEO MODULATOR 16-SOIC |
| MC44BS374T1AEFR2 | IC AUDIO/VIDEO MODULATOR 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33989PEG | 功能描述:CAN 接口集成电路 SBC-HS RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33989PEGR2 | 功能描述:CAN 接口集成电路 SBC-HS RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33990D | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC33990DR2 | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC33991DW | 制造商:Freescale Semiconductor 功能描述:Gauge Driver Integrated Circuit |
发布紧急采购，3分钟左右您将得到回复。