- 您现在的位置：买卖IC网 > PDF目录16417 > MC3PHACVDW (Freescale Semiconductor)IC MOTOR CONTROLLER 28-SOIC PDF资料下载
参数资料
| 型号： | MC3PHACVDW |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 10/36页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR CONTROLLER 28-SOIC |
| 标准包装： | 26 |
| 应用： | AC 电机控制器，3 相 |
| 输出数： | 1 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Features
MOTOR PHASE CURRENT WAVEFORMS
COMPENSATED
UNCOMPENSATED
REMOVES 60 Hz HUM
AND DECREASES I 2 R LOSSES
PWM1
PWM2
MC3PHAC
PWM3
PWM4
CORRECTED PWMs
PWM5
PWM6
Figure 4. Dynamic Bus Ripple Cancellation
In standalone mode, the base frequency and PWM polarity are specified at the same time during
initialization by connecting either pin 25, 26, 27, or 28 exclusively to the PWMPOL_BASEFREQ input.
During initialization, pins 25, 26, 27, and 28 are cycled one at a time to determine which one has been
connected to the PWMPOL_BASEFREQ input.
made. Refer to the standalone mode schematic, Figure 8 . Only one of these jumpers (JP1–JP4) can be
connected at any one time.
NOTE
It is not necessary to break this connection once the initialization phase has
been completed. The MC3PHAC will function properly while this
connection is in place.
Table 3. PWM Polarity and Base Frequency Specification in Standalone Mode
Pin Connected to
PWMPOL_BASEFREQ Pin
MUX_IN (JP1)
SPEED (JP2)
ACCEL (JP3)
DC_BUS (JP4)
PWM Polarity
Logic low = on
Logic high = on
Logic low = on
Logic high = on
Base Frequency
50 Hz
50 Hz
60 Hz
60 Hz
MC3PHAC Monolithic Intelligent Motor Controller, Rev. 2
10
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| UVP1V4R7MDD | CAP ALUM 4.7UF 35V 20% RADIAL |
| H1WXH-6036G | IDC CABLE - HPL60H/AE60G/X |
| 6278876-1 | C/A 50.125UM RIS MTRJ 1M1 |
| RBM12DCWT | CONN EDGECARD 24POS DIP .156 SLD |
| UVP1A470MDD | CAP ALUM 47UF 10V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC3PHACVDWE | 功能描述:马达/运动/点火控制器和驱动器 8BIT MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC3PHACVFA | 制造商:Freescale Semiconductor 功能描述:MCU 8BIT HC08 CISC 8KB FLASH 5V 32LQFP - Trays 制造商:Rochester Electronics LLC 功能描述:8BIT MCU, 8K FLASH OTP - Bulk |
| MC3PHACVFAE | 功能描述:马达/运动/点火控制器和驱动器 8B MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC3PHACVP | 制造商:Freescale Semiconductor 功能描述:MCU 8BIT HC08 CISC 8KB FLASH 5V 28PDIP - Rail/Tube 制造商:Freescale Semiconductor 功能描述:Controller IC |
| MC3PHACVPE | 功能描述:马达/运动/点火控制器和驱动器 8BIT MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。