参数资料
型号: MC56F8011VFAE
厂商: Freescale Semiconductor
文件页数: 81/126页
文件大小: 0K
描述: IC DIGITAL SIGNAL CTLR 32-LQFP
标准包装: 250
系列: 56F8xxx
核心处理器: 56800E
芯体尺寸: 16-位
速度: 32MHz
连通性: I²C,SCI,SPI
外围设备: POR,PWM,WDT
输入/输出数: 26
程序存储器容量: 12KB(6K x 16)
程序存储器类型: 闪存
RAM 容量: 1K x 16
电压 - 电源 (Vcc/Vdd): 3 V ~ 3.6 V
数据转换器: A/D 6x12b
振荡器型: 内部
工作温度: -40°C ~ 105°C
封装/外壳: 32-LQFP
包装: 托盘
配用: CPA56F8013-ND - BOARD SOCKET FOR MC56F8013
APMOTOR56F8000E-ND - KIT DEMO MOTOR CTRL SYSTEM
56F8013/56F8011 Data Sheet, Rev. 12
58
Freescale Semiconductor
5.5.6
Vector Base Address Register (VBA)
Figure 5-8 Vector Base Address Register (VBA)
5.5.6.1
Reserved—Bits 15–14
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
5.5.6.2
Vector Address Bus (VAB) Bits 13—0
The value in this register is used as the upper 14 bits of the interrupt vector VAB[20:0]. The lower 7 bits
are determined based on the highest priority interrupt and are then appended onto VBA before presenting
the full VAB to the Core.
5.5.7
Fast Interrupt Match 0 Register (FIM0)
Figure 5-9 Fast Interrupt Match 0 Register (FIM0)
5.5.7.1
Reserved—Bits 15–6
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
5.5.7.2
Fast Interrupt 0 Vector Number (FAST INTERRUPT 0)—Bits 5–0
These values determine which IRQ will be Fast Interrupt 0. Fast Interrupts vector directly to a service
routine based on values in the Fast Interrupt Vector Address registers without having to go to a jump table
first. IRQs used as Fast Interrupts must be set to priority level 2. Unexpected results will occur if a Fast
Interrupt vector is set to any other priority. A Fast Interrupt automatically becomes the highest-priority
level 2 interrupt regardless of its location in the interrupt table prior to being declared as Fast Interrupt.
Fast Interrupt 0 has priority over Fast Interrupt 1. To determine the vector number of each IRQ, refer to
the vector table.
Base + $5
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Read
0
VECTOR_BASE_ADDRESS
Write
RESET1
1. The 56F8013 resets to a value of 0x0000. This corresponds to reset addresses of 0x000000.
The 56F8011 resets to a value of 0x0010. This corresponds to reset addresses of 0x000800.
0
000
0
0000000
0
Base + $6
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Read
0
FAST INTERRUPT 0
Write
RESET
00000
0000000
0000
相关PDF资料
PDF描述
S9S08DN32F1MLC IC MCU 8BIT 32KB FLASH 32LQFP
MC9S08MM32VLH IC MCU 8BIT 32K FLASH 64LQFP
MC9S08JE128CMB IC MCU 8BIT 128K FLASH 81MAPBGA
MC9S08AW60VFGE IC MCU 8BIT 60KB FLASH 44-LQFP
MC9S08DN32AVLF MCU 8BIT 32K FLASH 48-LQFP
相关代理商/技术参数
参数描述
MC56F8013 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers
MC56F8013E 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers
MC56F8013MFAE 功能描述:数字信号处理器和控制器 - DSP, DSC 16Bit DSPHC ANGUILLA RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
MC56F8013MFAER2 制造商:Freescale Semiconductor 功能描述:16 BIT DSPHC ANGUILLA - Tape and Reel
MC56F8013PB 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers