收藏本站
参数资料
型号： MC68HC08QY4MDW
厂商： FREESCALE SEMICONDUCTOR INC
元件分类： 微控制器/微处理器
英文描述： 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
封装： 1.27 MM PITCH, PLASTIC, MS-013AA, SOIC-16
文件页数： 18/178页
文件大小： 2311K
代理商： MC68HC08QY4MDW
System Integration Module (SIM)
MC68HC08QY/QT Family Data Sheet, Rev. 1
114
Freescale Semiconductor
13.6.3 Reset
All reset sources always have equal and highest priority and cannot be arbitrated.
13.6.4 Break Interrupts
The break module can stop normal program flow at a software programmable break point by asserting its
break interrupt output. (See Chapter 15 Development Support.) The SIM puts the CPU into the break
state by forcing it to the SWI vector location. Refer to the break interrupt subsection of each module to
see how each module is affected by the break state.
13.6.5 Status Flag Protection in Break Mode
The SIM controls whether status flags contained in other modules can be cleared during break mode. The
user can select whether flags are protected from being cleared by properly initializing the break clear flag
enable bit (BCFE) in the break flag control register (BFCR).
Protecting flags in break mode ensures that set flags will not be cleared while in break mode. This
protection allows registers to be freely read and written during break mode without losing status flag
information.
Setting the BCFE bit enables the clearing mechanisms. Once cleared in break mode, a flag remains
cleared even when break mode is exited. Status flags with a two-step clearing mechanism — for example,
a read of one register followed by the read or write of another — are protected, even when the first step
is accomplished prior to entering break mode. Upon leaving break mode, execution of the second step
will clear the flag as normal.
13.7 Low-Power Modes
Executing the WAIT or STOP instruction puts the MCU in a low power- consumption mode for standby
situations. The SIM holds the CPU in a non-clocked state. The operation of each of these modes is
described below. Both STOP and WAIT clear the interrupt mask (I) in the condition code register, allowing
interrupts to occur.
13.7.1 Wait Mode
In wait mode, the CPU clocks are inactive while the peripheral clocks continue to run. Figure 13-14 shows
the timing for wait mode entry.
Figure 13-14. Wait Mode Entry Timing
A module that is active during wait mode can wake up the CPU with an interrupt if the interrupt is enabled.
Stacking for the interrupt begins one cycle after the WAIT instruction during which the interrupt occurred.
WAIT ADDR + 1
SAME
ADDRESS BUS
DATA BUS
PREVIOUS DATA
NEXT OPCODE
SAME
WAIT ADDR
SAME
R/W
NOTE: Previous data can be operand data or the WAIT opcode, depending on the last instruction.
相关PDF资料
PDF描述
MC68HC08QY4VDTE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
MC9S12XD64VAA 16-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP80
MP-1-12.0288MHZ QUARTZ CRYSTAL RESONATOR, 12.0288 MHz
MP-14.0960MHZ QUARTZ CRYSTAL RESONATOR, 4.096 MHz
MP-1-RFREQ11 QUARTZ CRYSTAL RESONATOR, 20 MHz - 34 MHz
相关代理商/技术参数
参数描述
MC68HC08SR12 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers
MC68HC08TV24CFB 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers
MC68HC08XL36 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit
MC68HC08XL36CB 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit
MC68HC08XL36CFU 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*