参数资料
型号: MC68HC11F1CPU4
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, EEPROM, 4 MHz, MICROCONTROLLER, PQFP80
封装: 14 X 14 MM, 1.40 MM HEIGHT, LQFP-80
文件页数: 105/162页
文件大小: 4554K
代理商: MC68HC11F1CPU4
OPERATING MODES AND ON-CHIP MEMORY
MOTOROLA
TECHNICAL DATA
4-9
4.3.2 Initialization
Because bits in the following registers control the basic configuration of the MCU, an
accidental change of their values could cause serious system problems. The protec-
tion mechanism, overridden in special operating modes, requires a write to the protect-
ed bits only within the first 64 bus cycles after any reset, or only once after each reset.
Table 4-2 summarizes the write access limited registers.
4.3.2.1 CONFIG Register
CONFIG controls the presence and position of the EEPROM in the memory map.
CONFIG also enables the COP watchdog timer.
P indicates a previously programmed bit. P(L) indicates that the bit resets to the logic
level held in the latch prior to reset, but the function of COP is controlled by DISR bit
in TEST1 register.
The CONFIG register consists of an EEPROM byte and static latches that control the
start-up conguration of the MCU. The contents of the EEPROM byte are transferred
into static working latches during reset sequences. The operation of the MCU is con-
trolled directly by these latches and not by CONFIG itself. In normal modes, changes
to CONFIG do not affect operation of the MCU until after the next reset sequence.
When programming, the CONFIG register itself is accessed. When the CONFIG reg-
ister is read, the static latches are accessed.
These bits can be read at any time. The value read is the one latched into the register
from the EEPROM cells during the last reset sequence. A new value programmed into
this register cannot be read until after a subsequent reset sequence. Unused bits al-
ways read as ones.
In special test mode, the static latches can be written directly at any time. In all modes,
CONFIG bits can only be programmed using the EEPROM programming sequence,
and are neither readable nor active until latched via the next reset. Refer to 4.4.3 CON-
EE[3:0] — EEPROM Mapping Control
EE[3:0] select the upper four bits of the EEPROM base address. In single-chip and
bootstrap modes, EEPROM is forced to $FE00–$FFFF regardless of the value of
EE[3:0].
CONFIG — System Configuration Register
$103F
Bit 7
654321
Bit 0
EE3
EE2
EE1
EE0
NOCOP
EEON
RESET:
11111
P
11
Single Chip
11111
P(L)
1
Bootstrap
P
P1P1P
Expanded
PPPP
1
P(L)
1
0
Special Test
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相关PDF资料
PDF描述
MC68322FT20 16-BIT, 20 MHz, RISC PROCESSOR, PQFP160
MC68HC08AS32VAFN 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQCC52
MC68HRC98JL3EMP 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP28
MC9S12B64CPV16 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP112
MC68HC05C4AB 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP42
相关代理商/技术参数
参数描述
MC68HC11F1CPU5 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller
MC68HC11F1CPUE5 制造商:Freescale Semiconductor 功能描述:
MC68HC11F1FB 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1FB1 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers
MC68HC11F1FB3 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers