参数资料
型号: MC68HC705P6AVDW
厂商: MOTOROLA INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO28
封装: SOIC-28
文件页数: 64/130页
文件大小: 1541K
代理商: MC68HC705P6AVDW
Operating Modes
Low-Power Modes
MC68HC705P6A — Rev. 2.0
Advance Information
MOTOROLA
Operating Modes
39
The MCU can be brought out of stop mode only by an IRQ external
interrupt or an externally generated RESET. When exiting stop mode,
the internal oscillator will resume after a 4064 internal clock cycle
oscillator stabilization delay.
NOTE:
Execution of the STOP instruction when the SWAIT bit in the MOR is
clear will cause the oscillator to stop, and, therefore, disable the COP
watchdog timer. To avoid turning off the COP watchdog timer, stop
mode should be changed to halt mode by setting the SWAIT bit in the
MOR. See 3.6 COP Watchdog Timer Considerations for additional
information.
3.5.1.2 Halt Mode
NOTE:
Halt mode is NOT designed for intentional use. Halt mode is only
provided to keep the COP watchdog timer active in the event a STOP
instruction is executed inadvertently. This mode of operation is usually
achieved by invoking wait mode.
Execution of the STOP instruction when the SWAIT bit in the MOR is set
places the MCU in this low-power mode. Halt mode consumes the same
amount of power as wait mode (both halt and wait modes consume more
power than stop mode).
In halt mode, the internal clock is halted, suspending all processor and
internal bus activity. Internal timer clocks remain active, permitting
interrupts to be generated from the 16-bit timer or a reset to be
generated from the COP watchdog timer. Execution of the STOP
instruction automatically clears the I bit in the condition code register,
enabling the IRQ external interrupt. All other registers, memory, and
input/output lines remain in their previous states.
If the 16-bit timer interrupt is enabled, it will cause the processor to exit
the halt mode and resume normal operation. The halt mode also can be
exited when an IRQ external interrupt or external RESET occurs.
When exiting the halt mode, the internal clock will resume after a delay
of one to 4064 internal clock cycles. This varied delay time is the result
of the halt mode exit circuitry testing the oscillator stabilization delay
相关PDF资料
PDF描述
ML9042-11CVWA 17 X 100 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC233
MSP430G2131IRSA16 16-BIT, FLASH, RISC MICROCONTROLLER, PQCC16
MC68HLC908QY4DT 8-BIT, FLASH, 2 MHz, MICROCONTROLLER, PDSO16
MC9S12C64PVFU16 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP80
MPC9230FNR2 800 MHz, OTHER CLOCK GENERATOR, PQCC28
相关代理商/技术参数
参数描述
MC68HC705P6CDW 制造商:Motorola Inc 功能描述:
MC68HC705P6CP 制造商:Freescale Semiconductor 功能描述: 制造商:Motorola Inc 功能描述:
MC68HC705P6ECDW 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述:
MC68HC705SR3CP 功能描述:IC MCU 3.75K 2.1MHZ OTP 40-DIP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 其它有关文件:STM32F101T8 View All Specifications 特色产品:STM32 32-bit Cortex MCUs 标准包装:490 系列:STM32 F1 核心处理器:ARM? Cortex?-M3 芯体尺寸:32-位 速度:36MHz 连通性:I²C,IrDA,LIN,SPI,UART/USART 外围设备:DMA,PDR,POR,PVD,PWM,温度传感器,WDT 输入/输出数:26 程序存储器容量:64KB(64K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):2 V ~ 3.6 V 数据转换器:A/D 10x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:36-VFQFN,36-VFQFPN 包装:托盘 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名称:497-9032STM32F101T8U6-ND
MC68HC705SR3CPE 功能描述:8位微控制器 -MCU 8B MCU 192 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT