参数资料
型号: MC68HLC908QY1CDW
厂商: MOTOROLA INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 2 MHz, MICROCONTROLLER, PDSO16
封装: SOIC-16
文件页数: 116/186页
文件大小: 2583K
代理商: MC68HLC908QY1CDW
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页当前第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页
Memory
FLASH Memory (FLASH)
MC68HLC908QY/QT Family — Rev. 2
Data Sheet
MOTOROLA
Memory
35
1.
Set the PGM bit. This configures the memory for program operation and
enables the latching of address and data for programming.
2.
Read the FLASH block protect register.
3.
Write any data to any FLASH location within the address range desired.
4.
Wait for a time, tNVS (minimum 10 s).
5.
Set the HVEN bit.
6.
Wait for a time, tPGS (minimum 5 s).
7.
Write data to the FLASH address being programmed(1).
8.
Wait for time, tPROG (minimum 30 s).
9.
Repeat step 7 and 8 until all desired bytes within the row are programmed.
10.
Clear the PGM bit(1).
11.
Wait for time, tNVH (minimum 5 s).
12.
Clear the HVEN bit.
13.
After time, tRCV (typical 1 s), the memory can be accessed in read mode
again.
NOTE:
The COP register at location $FFFF should not be written between steps 5-12,
when the HVEN bit is set. Since this register is located at a valid FLASH address,
unpredictable behavior may occur if this location is written while HVEN is set.
This program sequence is repeated throughout the memory until all data is
programmed.
NOTE:
Programming and erasing of FLASH locations cannot be performed by code being
executed from the FLASH memory. While these operations must be performed in
the order shown, other unrelated operations may occur between the steps. Do not
exceed tPROG maximum, see 16.12 Memory Characteristics.
2.6.5 FLASH Protection
Due to the ability of the on-board charge pump to erase and program the FLASH
memory in the target application, provision is made to protect blocks of memory
from unintentional erase or program operations due to system malfunction. This
protection is done by use of a FLASH block protect register (FLBPR). The FLBPR
determines the range of the FLASH memory which is to be protected. The range
of the protected area starts from a location defined by FLBPR and ends to the
bottom of the FLASH memory ($FFFF). When the memory is protected, the HVEN
bit cannot be set in either ERASE or PROGRAM operations.
NOTE:
In performing a program or erase operation, the FLASH block protect register must
be read after setting the PGM or ERASE bit and before asserting the HVEN bit.
1. The time between each FLASH address change, or the time between the last FLASH address
programmed to clearing PGM bit, must not exceed the maximum programming time, tPROG
maximum.
相关PDF资料
PDF描述
M3062CF8TGP 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
MC908AB32CFU 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64
MC68HC11D3CP 8-BIT, 2 MHz, MICROCONTROLLER, PDIP40
M30290FCVHP 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP80
M30291M8T-XXXHP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
MC68HLC908QY1DT 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
MC68HLC908QY2CDT 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HLC908QY2CDW 制造商:Rochester Electronics LLC 功能描述:LOW V-1.5K FLASH W/ADC - Bulk
MC68HLC908QY2CP 制造商:Rochester Electronics LLC 功能描述:LOW V-1.5K FLASH W/ADC - Bulk
MC68HLC908QY2DW 制造商:Rochester Electronics LLC 功能描述:- Bulk