参数资料
型号: MC7410VU500LE
厂商: Freescale Semiconductor
文件页数: 39/56页
文件大小: 0K
描述: IC MPU RISC 32BIT 360-FCCBGA
标准包装: 44
系列: MPC74xx
处理器类型: 32-位 MPC74xx PowerPC
速度: 500MHz
电压: 1.8V
安装类型: 表面贴装
封装/外壳: 360-BCBGA,FCCBGA
供应商设备封装: 360-FCCBGA(25x25)
包装: 托盘
MPC7410 RISC Microprocessor Hardware Specifications, Rev. 6.1
44
Freescale Semiconductor
System Design Information
8.8.1 Internal Package Conduction Resistance
For the exposed-die packaging technology, shown in Table 3, the intrinsic conduction thermal resistance paths are
as follows:
The die junction-to-case (or top-of-die for exposed silicon) thermal resistance
The die junction-to-ball thermal resistance
Figure 28 depicts the primary heat transfer path for a package with an attached heat sink mounted to a printed-circuit
board.
Heat generated on the active side of the chip is conducted through the silicon, then through the heat sink attach
material (or thermal interface material), and finally to the heat sink where it is removed by forced-air convection.
Since the silicon thermal resistance is quite small, for a first-order analysis, the temperature drop in the silicon may
be neglected. Thus, the heat sink attach material and the heat sink conduction/convective thermal resistances are the
dominant terms.
Figure 28. C4 Package with Heat Sink Mounted to a Printed-Circuit Board
8.8.2 Adhesives and Thermal Interface Materials
A thermal interface material is recommended at the package lid-to-heat sink interface to minimize the thermal
contact resistance. For those applications where the heat sink is attached by spring clip mechanism, Figure 29 shows
the thermal performance of three thin-sheet thermal-interface materials (silicone, graphite/oil, floroether oil), a bare
joint, and a joint with thermal grease as a function of contact pressure. As shown, the performance of these thermal
interface materials improves with increasing contact pressure. The use of thermal grease significantly reduces the
interface thermal resistance. That is, the bare joint results in a thermal resistance approximately seven times greater
than the thermal grease joint.
Heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit board (see Figure 26).
This spring force should not exceed 5.5 pounds of force. Therefore, the synthetic grease offers the best thermal
performance, considering the low interface pressure. Of course, the selection of any thermal interface material
depends on many factors—thermal performance requirements, manufacturability, service temperature, dielectric
properties, cost, and so on.
External Resistance
Internal Resistance
Note the internal versus external package resistance.
Radiation
Convection
Radiation
Convection
Heat Sink
Printed-Circuit Board
Thermal Interface Material
Package/Leads
Die Junction
Die/Package
相关PDF资料
PDF描述
ACB108DHAN CONN EDGECARD 216PS R/A .050 DIP
IDT70V9369L9PF8 IC SRAM 288KBIT 9NS 100TQFP
MPC7410VS500LE IC MPU PPC 500MHZ 360-FCCLGA
MPC8567VTAUJJ MPU POWERQUICC III 1023-PBGA
IDT70V9179L9PF8 IC SRAM 288KBIT 9NS 100TQFP
相关代理商/技术参数
参数描述
MC7411MEL 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC7412 制造商:SHENZHENFREESCALE 制造商全称:ShenZhen FreesCale Electronics. Co., Ltd 功能描述:N-Channel 20V (D-S) MOSFET High performance trench technology
MC7413 制造商:SHENZHENFREESCALE 制造商全称:ShenZhen FreesCale Electronics. Co., Ltd 功能描述:P-Channel 20-V (D-S) MOSFET High performance trench technology
MC7415 制造商:SHENZHENFREESCALE 制造商全称:ShenZhen FreesCale Electronics. Co., Ltd 功能描述:P-Channel 20-V (D-S) MOSFET High performance trench technology
MC74195L 制造商:Rochester Electronics LLC 功能描述:- Bulk