参数资料
型号: MC7457VG867LC
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 32-BIT, 867 MHz, RISC PROCESSOR, CBGA483
封装: 29 X 29 MM, 3.22 MM HEIGHT, 1.27 MM PITCH, ROHS COMPLIANT, CERAMIC, BGA-483
文件页数: 37/72页
文件大小: 1598K
代理商: MC7457VG867LC
MPC7457 RISC Microprocessor Hardware Specifications, Rev. 7
42
Freescale Semiconductor
Pinout Listings
TDI
E4
High
Input
BVSEL
7
TDO
H1
High
Output
BVSEL
TEA
T1
Low
Input
BVSEL
TEST[0:5]
B10, H6, H10, D8, F9, F8
Input
BVSEL
13
TEST[6]
A9
Input
BVSEL
10
TMS
K4
High
Input
BVSEL
7
TRST
C1
Low
Input
BVSEL
7, 16
TS
P5
Low
I/O
BVSEL
3
TSIZ[0:2]
L1,H3,D1
High
Output
BVSEL
TT[0:4]
F1, F4, K8, A5, E1
High
I/O
BVSEL
WT
L2
Low
Output
BVSEL
VDD
J9, J11, J13, J15, K10, K12, K14, L9, L11, L13, L15,
M10, M12, M14, N9, N11, N13, N15, P10, P12, P14
——
N/A
VDD_SENSE[0:1]
G11, J8
N/A
17
Notes:
1. OVDD supplies power to the processor bus, JTAG, and all control signals except the L3 cache controls (L3CTL[0:1]); GVDD
supplies power to the L3 cache interface (L3ADDR[0:17], L3DATA[0:63], L3DP[0:7], L3_ECHO_CLK[0:3], and L3_CLK[0:1])
and the L3 control signals L3_CNTL[0:1]; and VDD supplies power to the processor core and the PLL (after filtering to become
AVDD). For actual recommended value of Vin or supply voltages, see Table 4.
2. Unused address pins must be pulled down to GND.
3. These pins require weak pull-up resistors (for example, 4.7 k
Ω) to maintain the control signals in the negated state after they
have been actively negated and released by the MPC7457 and other bus masters.
4. This signal selects between MPX bus mode (asserted) and 60x bus mode (negated) and will be sampled at HRESET going
high.
5. This signal must be negated during reset, by pull up to OVDD or negation by HRESET (inverse of HRESET), to ensure
proper operation.
6. See Table 3 for bus voltage configuration information. If used, pull-down resistors should be less than 250
Ω.
7. Internal pull up on die.
8. Ignored in 60x bus mode.
9. These signals must be pulled down to GND if unused or if the MPC7457 is in 60x bus mode.
10.These input signals for factory use only and must be pulled down to GND for normal machine operation.
11.Power must be supplied to GVDD, even when the L3 interface is disabled or unused.
12.This test signal is recommended to be tied to HRESET; however, other configurations will not adversely affect performance.
13.These input signals are for factory use only and must be pulled up to OVDD for normal machine operation.
14.These signals are for factory use only and must be left unconnected for normal machine operation.
15.This pin can externally cause a performance monitor event. Counting of the event is enabled via software.
16.This signal must be asserted during reset, by pull down to GND or assertion by HRESET, to ensure proper operation.
17.These pins are internally connected to VDD. They are intended to allow an external device to detect the core voltage level
present at the processor core. If unused, they must be connected directly to VDD or left unconnected.
Table 17. Pinout Listing for the MPC7457, 483 CBGA Package (continued)
Signal Name
Pin Number
Active
I/O
I/F Select 1
Notes
相关PDF资料
PDF描述
MC3S12HN32J3CAA 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80
MC3S12HN64J3CAL 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP112
MB95F354LPFT-G-SNE2 MICROCONTROLLER, PDSO24
MPC8540CPXAQFC 32-BIT, 667 MHz, MICROPROCESSOR, PBGA783
MPC8555VTAPFX 32-BIT, 833 MHz, RISC PROCESSOR, PBGA783
相关代理商/技术参数
参数描述
MC7457VG867NC 功能描述:微处理器 - MPU APOLO7 RV1.2 1.1V 105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MC74A5-33SNTR 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
MC74A5-50T 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
MC74AC00 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:QUAD 2-INPUT NAND GATE
MC74AC00D 功能描述:逻辑门 2-6V Quad 2-Input RoHS:否 制造商:Texas Instruments 产品:OR 逻辑系列:LVC 栅极数量:2 线路数量(输入/输出):2 / 1 高电平输出电流:- 16 mA 低电平输出电流:16 mA 传播延迟时间:3.8 ns 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:DCU-8 封装:Reel