参数资料
| 型号： | MC74HC4066AFEL |
| 厂商： | ON Semiconductor |
| 文件页数： | 3/14页 |
| 文件大小： | 0K |
| 描述： | IC MUX/DEMUX QUAD 1X1 14SOEIAJ |
| 产品变化通告： | Product Obsolescence 24/Jan/2011 |
| 标准包装： | 2,000 |
| 系列： | 74HC |
| 功能： | 多路复用器/多路分解器 |
| 电路： | 4 x 1:1 |
| 导通状态电阻： | 100 欧姆 |
| 电压电源： | 双电源 |
| 电压 - 电源，单路/双路(±)： | ±2 V ~ 12 V |
| 电流 - 电源： | 40µA |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.209"，5.30mm 宽） |
| 供应商设备封装： | SOEIAJ-14 |
| 包装： | 带卷 (TR) |
MC74HC4066A
http://onsemi.com
11
0
-10
-20
-30
-40
-50
1.0
2.0
FREQUENCY (kHz)
dBm
-60
-70
-80
-90
FUNDAMENTAL FREQUENCY
DEVICE
SOURCE
Figure 15. Plot, Harmonic Distortion
3.0
APPLICATION INFORMATION
The ON/OFF Control pins should be at VCC or GND logic
levels, VCC being recognized as logic high and GND being
recognized as a logic low. Unused analog inputs/outputs
may be left floating (not connected). However, it is
advisable to tie unused analog inputs and outputs to VCC or
GND through a low value resistor. This minimizes crosstalk
and feedthrough noise that may be pickedup by the unused
I/O pins.
The maximum analog voltage swings are determined by
the supply voltages VCC and GND. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below GND. In the example
below, the difference between VCC and GND is twelve volts.
Therefore, using the configuration in Figure 16, a maximum
analog signal of twelve volts peaktopeak can be
controlled.
When voltage transients above VCC and/or below GND
are anticipated on the analog channels, external diodes (Dx)
are recommended as shown in Figure 17. These diodes
should be small signal, fast turnon types able to absorb the
maximum anticipated current surges during clipping. An
alternate method would be to replace the Dx diodes with
Mosorbs (Mosorb
is an acronym for high current surge
protectors). Mosorbs are fast turnon devices ideally suited
for precise DC protection with no inherent wear out
mechanism.
ANALOG O/I
ON
14
VCC = 12 V
ANALOG I/O
+ 12 V
0 V
+ 12 V
0 V
OTHER CONTROL
INPUTS
(VCC OR GND)
ON
16
VCC
Dx
VCC
Dx
Figure 16. 12 V Application
Figure 17. Transient Suppressor Application
7
SELECTED
CONTROL
INPUT
Dx
OTHER CONTROL
INPUTS
(VCC OR GND)
7
SELECTED
CONTROL
INPUT
VCC
相关PDF资料 |
PDF描述 |
|---|---|
| MC74HC4067ADWG | IC MUX/DEMUX/QUAD SWITCH 24SOIC |
| MC74HC4316AFELG | IC MUX/DEMUX QUAD 1X1 16SOEIAJ |
| MC74HC4852AN | IC MUX/DEMUX DUAL 4X1 16DIP |
| MC74HCT4051ADTG | ANALOG MULTIPLEXERS/DEMU TSSOP16 |
| MC74HCT4852ADTG | LOG CMOS MLTIPLXR ANALOG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC74HC4066AFELG | 功能描述:多路器开关 IC 2-12V Quad Mux/Demux -55 to 85deg C RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MC74HC4066AN | 功能描述:多路器开关 IC 2-12V Quad Mux/Demux RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MC74HC4066ANG | 功能描述:多路器开关 IC 2-12V Quad Mux/Demux -55 to 85deg C RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MC74HC4066D | 制造商:Motorola Inc 功能描述: |
| MC74HC4066DR2 | 制造商:Motorola Inc 功能描述: 制造商:ON Semiconductor 功能描述: |
发布紧急采购，3分钟左右您将得到回复。