- 您现在的位置：买卖IC网 > PDF目录382312 > MC74LVXT4066DT (ON SEMICONDUCTOR) Quad Analog Switch/Multiplexer/Demultiplexer PDF资料下载
参数资料
| 型号： | MC74LVXT4066DT |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 运动控制电子 |
| 英文描述： | Quad Analog Switch/Multiplexer/Demultiplexer |
| 中文描述： | QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO14 |
| 封装： | TSSOP-14 |
| 文件页数： | 8/12页 |
| 文件大小： | 265K |
| 代理商： | MC74LVXT4066DT |
MC74LVXT4066
http://onsemi.com
8
0
–10
–20
–30
–40
–50
1.0
2.0
FREQUENCY (kHz)
d
–60
–70
–80
–90
FUNDAMENTAL FREQUENCY
DEVICE
SOURCE
Figure 15. Plot, Harmonic Distortion
3.0
APPLICATION INFORMATION
The ON/OFF Control pins should be at VIH or VIL logic
levels, VIH being recognized as logic high and VIL being
recognized as a logic low. Unused analog inputs/outputs
may be left floating (not connected). However, it is
advisable to tie unused analog inputs and outputs to VCC or
GND through a low value resistor. This minimizes crosstalk
and feedthrough noise that may be picked–up by the unused
I/O pins.
The maximum analog voltage swings are determined by
the supply voltages VCC and GND. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below GND. In the example
below, the difference between VCC and GND is six volts.
Therefore, using the configuration in Figure 16, a maximum
analog signal of six volts peak–to–peak can be controlled.
When voltage transients above VCC and/or below GND
are anticipated on the analog channels, external diodes (Dx)
are recommended as shown in Figure 17. These diodes
should be small signal, fast turn–on types able to absorb the
maximum anticipated current surges during clipping. An
alternate method would be to replace the Dx diodes with
Mosorbs (Mosorb
is an acronym for high current surge
protectors). Mosorbs are fast turn–on devices ideally suited
for precise DC protection with no inherent wear out
mechanism.
ANALOG O/I
ON
14
VCC = 6.0 V
ANALOG I/O
+ 6.0 V
0 V
+ 6.0 V
0 V
OTHER CONTROL
INPUTS
(VIH OR VIL)
ON
16
VCC
Dx
Dx
VCC
Dx
Figure 16. 6.0 V Application
Figure 17. Transient Suppressor Application
7
SELECTED
CONTROL
INPUT
Dx
OTHER CONTROL
INPUTS
(VIH OR VIL)
7
SELECTED
CONTROL
INPUT
VIH
VIH
相关PDF资料 |
PDF描述 |
|---|---|
| MC74LVXT4066DTR2 | Quad Analog Switch/Multiplexer/Demultiplexer |
| MC74LVXT8051DR2 | Analog Multiplexer/Demultiplexer |
| MC74LVXT8051 | Analog Multiplexer/Demultiplexer |
| MC74LVXT8051D | Analog Multiplexer/Demultiplexer |
| MC74LVXT8051DT | Analog Multiplexer/Demultiplexer |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC74LVXT4066DTR2 | 功能描述:多路器开关 IC 2-6V ANLG Mux/Demux RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MC74LVXT4066DTRG | 功能描述:模拟开关 IC 2-6V ANLG Mux/Demux -55 to 85deg C RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MC74LVXT4066DTRG-CUT TAPE | 制造商:ON 功能描述:MC74LVXT4066 Series 2 to 5.5 V Quad Analog Switch/Mux/Demux - TSSOP-14 |
| MC74LVXT4066M | 功能描述:模拟开关 IC 2-6V ANLG Mux/Demux RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MC74LVXT4066MEL | 功能描述:模拟开关 IC 2-6V ANLG Mux/Demux RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
发布紧急采购，3分钟左右您将得到回复。