参数资料
型号: MC908QY2CDWR2
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
封装: 1.27 MM PITCH, PLASTIC, MS-013AA, SOIC-16
文件页数: 48/184页
文件大小: 1763K
代理商: MC908QY2CDWR2
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页当前第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页
Monitor Module (MON)
MC68HC908QY/QT Family Data Sheet, Rev. 5
Freescale Semiconductor
141
Figure 15-12. Monitor Mode Circuit (Internal Clock, No High Voltage)
Simple monitor commands can access any memory address. In monitor mode, the MCU can execute
code downloaded into RAM by a host computer while most MCU pins retain normal operating mode
functions. All communication between the host computer and the MCU is through the PTA0 pin. A
level-shifting and multiplexing interface is required between PTA0 and the host computer. PTA0 is used
in a wired-OR configuration and requires a pullup resistor.
The monitor code has been updated from previous versions of the monitor code to allow enabling the
internal oscillator to generate the internal clock. This addition, which is enabled when IRQ is held low out
of reset, is intended to support serial communication/programming at 9600 baud in monitor mode by using
the internal oscillator, and the internal oscillator user trim value OSCTRIM (FLASH location $FFC0, if
programmed) to generate the desired internal frequency (3.2 MHz). Since this feature is enabled only
when IRQ is held low out of reset, it cannot be used when the reset vector is programmed (i.e., the value
is not $FFFF) because entry into monitor mode in this case requires VTST on IRQ. The IRQ pin must
remain low during this monitor session in order to maintain communication.
Table 15-1 shows the pin conditions for entering monitor mode. As specified in the table, monitor mode
may be entered after a power-on reset (POR) and will allow communication at 9600 baud provided one
of the following sets of conditions is met:
If $FFFE and $FFFF do not contain $FF (programmed state):
The external clock is 9.8304 MHz
–IRQ = VTST
If $FFFE and $FFFF contain $FF (erased state):
The external clock is 9.8304 MHz
–IRQ = VDD (this can be implemented through the internal IRQ pullup)
If $FFFE and $FFFF contain $FF (erased state):
–IRQ = VSS (internal oscillator is selected, no external clock required)
RST (PTA3)
IRQ (PTA2)
PTA0
10 k
*
OSC1 (PTA5)
N.C.
8
7
DB9
2
3
5
16
15
2
6
10
9
VDD
1
F
MAX232
C1+
C1–
V+
V–
5
4
1
F
C2+
C2–
VDD
1
F
+
1
2
3
4
5
6
74HC125
10 k
N.C.
PTA1
N.C.
PTA4
VSS
0.1
F
VDD
+
3
1
F
+
1
F
VDD
* Value not critical
N.C.
相关PDF资料
PDF描述
MC9328MX21CVKR2 32-BIT, 266 MHz, MICROPROCESSOR, PBGA289
MC9S08RC60CFJE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32
MC9S08RG60FGE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
MC9S12KG128VFUE 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80
MPC566CVR56 32-BIT, FLASH, 56 MHz, RISC MICROCONTROLLER, PBGA388
相关代理商/技术参数
参数描述
MC908QY2CFQE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers
MC908QY2CPE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers
MC908QY2DTE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers
MC908QY2DWE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers
MC908QY2FQE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers