参数资料
型号: MC908QY4MDWER
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
封装: 1.27 MM PITCH, ROHS COMPLIANT, PLASTIC, MS-013AA, SOIC-16
文件页数: 26/202页
文件大小: 2608K
代理商: MC908QY4MDWER
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页
Low-Power Modes
MC68HC908QYA/QTA Family Data Sheet, Rev. 2
Freescale Semiconductor
121
In wait mode, the CPU clocks are inactive. Refer to the wait mode subsection of each module to see if the
module is active or inactive in wait mode. Some modules can be programmed to be active in wait mode.
Wait mode can also be exited by a reset (or break in emulation mode). A break interrupt during wait mode
sets the SIM break stop/wait bit, SBSW, in the break status register (BSR). If the COP disable bit, COPD,
in the configuration register is 0, then the computer operating properly module (COP) is enabled and
remains active in wait mode.
Figure 13-15 and Figure 13-16 show the timing for wait recovery.
Figure 13-15. Wait Recovery from Interrupt
Figure 13-16. Wait Recovery from Internal Reset
13.7.2 Stop Mode
In stop mode, the SIM counter is reset and the system clocks are disabled. An interrupt request from a
module can cause an exit from stop mode. Stacking for interrupts begins after the selected stop recovery
time has elapsed. Reset or break also causes an exit from stop mode.
The SIM disables the oscillator signals (BUSCLKX2 and BUSCLKX4) in stop mode, stopping the CPU
and peripherals. If OSCENINSTOP is set, BUSCLKX2 will remain running in STOP and can be used to
run the AWU. Stop recovery time is selectable using the SSREC bit in the configuration register 1
(CONFIG1). If SSREC is set, stop recovery is reduced from the normal delay of 4096 BUSCLKX4 cycles
down to 32. This is ideal for the internal oscillator, RC oscillator, and external oscillator options which do
not require long start-up times from stop mode.
NOTE
External crystal applications should use the full stop recovery time by
clearing the SSREC bit.
$6E0C
$6E0B
$00FF
$00FE
$00FD
$00FC
$A6
$01
$0B
$6E
$A6
ADDRESS BUS
DATA BUS
EXITSTOPWAIT
NOTE: EXITSTOPWAIT = RST pin OR CPU interrupt
ADDRESS BUS
DATA BUS
RST(1)
$A6
$6E0B
RSTVCTH
RSTVCTL
$A6
BUSCLKX4
32
CYCLES
32
CYCLES
1. RST is only available if the RSTEN bit in the CONFIG1 register is set.
相关PDF资料
PDF描述
MC912B32MFU8R2 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80
MC932-11 0.1 A, 2 ELEMENT, SILICON, SIGNAL DIODE
MC9S12K Microcontrollers
MCA3703 1000 mA, 100 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET
MCBC2425DL
相关代理商/技术参数
参数描述
MC908QY4MFQE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers
MC908QY4MPE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers
MC908QY4PE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers
MC908QY4VDTE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers
MC908QY4VDWE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:M68HC08 Microcontrollers