参数资料
型号: MC9S12DB128VPV
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112
封装: LQFP-112
文件页数: 120/142页
文件大小: 6464K
代理商: MC9S12DB128VPV
Device User Guide — 9S12DT128DGV2/D V02.15
79
Freescale Semiconductor
4.3.3 Unsecuring the Microcontroller
In order to unsecure the microcontroller, the internal FLASH and EEPROM must be erased. This can be
done through an external program in expanded mode or via a .sequence of BDM commands. Unsecuring
is also possible via the Backdoor Key Access. Refer to Flash Block Guide for details.
Once the user has erased the FLASH and EEPROM, the part can be reset into special single chip mode.
This invokes a program that verifies the erasure of the internal FLASH and EEPROM. Once this program
completes, the user can erase and program the FLASH security bits to the unsecured state. This is generally
done through the BDM, but the user could also change to expanded mode (by writing the mode bits
through the BDM) and jumping to an external program (again through BDM commands). Note that if the
part goes through a reset before the security bits are reprogrammed to the unsecure state, the part will be
secured again.
4.4 Low Power Modes
The microcontroller features three main low power modes. Consult the respective Block User Guide for
information on the module behavior in Stop, Pseudo Stop, and Wait Mode. An important source of
information about the clock system is the Clock and Reset Generator User Guide (CRG).
4.4.1 Stop
Executing the CPU STOP instruction stops all clocks and the oscillator thus putting the chip in fully static
mode. Wake up from this mode can be done via reset or external interrupts.
4.4.2 Pseudo Stop
This mode is entered by executing the CPU STOP instruction. In this mode the oscillator is still running
and the Real Time Interrupt (RTI) or Watchdog (COP) sub module can stay active. Other peripherals are
turned off. This mode consumes more current than the full STOP mode, but the wake up time from this
mode is significantly shorter.
4.4.3 Wait
This mode is entered by executing the CPU WAI instruction. In this mode the CPU will not execute
instructions. The internal CPU signals (address and databus) will be fully static. All peripherals stay active.
For further power consumption the peripherals can individually turn off their local clocks.
4.4.4 Run
Although this is not a low power mode, unused peripheral modules should not be enabled in order to save
power.
相关PDF资料
PDF描述
MC9S12DJ128CPVR2 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112
SC515848CPV 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112
SC515847MFU 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80
MC9S12DJ128VPV 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112
MC9S12DJ128CFUE 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80
相关代理商/技术参数
参数描述
MC9S12DB128VPVE 功能描述:16位微控制器 - MCU MARLIN2 PB FREE RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MC9S12DG128BCFU 功能描述:16位微控制器 - MCU 16 Bit 25MHz RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MC9S12DG128BCPV 功能描述:16位微控制器 - MCU 16 Bit 25MHz RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MC9S12DG128BMFU 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC9S12DG128BVFU 功能描述:16位微控制器 - MCU 16 Bit 25MHz RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT