参数资料
型号: MC9S12DJ128EVPV
厂商: MOTOROLA INC
元件分类: 微控制器/微处理器
英文描述: 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112
封装: LQFP-112
文件页数: 116/138页
文件大小: 2093K
代理商: MC9S12DJ128EVPV
MC9S12DT128 Device User Guide — V02.11
79
4.3.3 Unsecuring the Microcontroller
In order to unsecure the microcontroller, the internal FLASH and EEPROM must be erased. This can be
done through an external program in expanded mode or via a .sequence of BDM commands. Unsecuring
is also possible via the Backdoor Key Access. Refer to Flash Block Guide for details.
Once the user has erased the FLASH and EEPROM, the part can be reset into special single chip mode.
This invokes a program that verifies the erasure of the internal FLASH and EEPROM. Once this program
completes, the user can erase and program the FLASH security bits to the unsecured state. This is generally
done through the BDM, but the user could also change to expanded mode (by writing the mode bits
through the BDM) and jumping to an external program (again through BDM commands). Note that if the
part goes through a reset before the security bits are reprogrammed to the unsecure state, the part will be
secured again.
4.4 Low Power Modes
The microcontroller features three main low power modes. Consult the respective Block User Guide for
information on the module behavior in Stop, Pseudo Stop, and Wait Mode. An important source of
information about the clock system is the Clock and Reset Generator User Guide (CRG).
4.4.1 Stop
Executing the CPU STOP instruction stops all clocks and the oscillator thus putting the chip in fully static
mode. Wake up from this mode can be done via reset or external interrupts.
4.4.2 Pseudo Stop
This mode is entered by executing the CPU STOP instruction. In this mode the oscillator is still running
and the Real Time Interrupt (RTI) or Watchdog (COP) sub module can stay active. Other peripherals are
turned off. This mode consumes more current than the full STOP mode, but the wake up time from this
mode is significantly shorter.
4.4.3 Wait
This mode is entered by executing the CPU WAI instruction. In this mode the CPU will not execute
instructions. The internal CPU signals (address and databus) will be fully static. All peripherals stay active.
For further power consumption the peripherals can individually turn off their local clocks.
4.4.4 Run
Although this is not a low power mode, unused peripheral modules should not be enabled in order to save
power.
相关PDF资料
PDF描述
M38223M4DXXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80
MB90347PFV 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100
MB90349CSPF 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100
MPC5602BEVLQR 32-BIT, FLASH, 64 MHz, MICROCONTROLLER, PQFP144
MB90F346ASPF 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
相关代理商/技术参数
参数描述
MC9S12DJ128MFUE 功能描述:16位微控制器 - MCU 128K FLASH HCS12 MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MC9S12DJ128MPVE 功能描述:16位微控制器 - MCU 128K FLASH HCS12 MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MC9S12DJ128VFUE 功能描述:16位微控制器 - MCU 128K FLASH HCS12 MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MC9S12DJ128VFUR2 制造商:Freescale Semiconductor 功能描述:16-BIT HCS12 CISC 128KB FLASH 2.5V/5V 80-PIN PQFP T/R - Tape and Reel
MC9S12DJ128VPVE 功能描述:16位微控制器 - MCU 128K FLASH HCS12 MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT