- 您现在的位置：买卖IC网 > PDF目录3789 > MCF52110CVM80J (Freescale Semiconductor)IC MCU 128K FLASH 80MHZ 81MAPBGA PDF资料下载
参数资料
| 型号： | MCF52110CVM80J |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 2/56页 |
| 文件大小： | 0K |
| 描述： | IC MCU 128K FLASH 80MHZ 81MAPBGA |
| 标准包装： | 1,200 |
| 系列： | MCF521xx |
| 核心处理器： | Coldfire V2 |
| 芯体尺寸： | 32-位 |
| 速度： | 80MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | DMA，LVD，POR，PWM，WDT |
| 输入/输出数： | 56 |
| 程序存储器容量： | 128KB（128K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 16K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 3 V ~ 3.6 V |
| 数据转换器： | A/D 8x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 81-LBGA |
| 包装： | 托盘 |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
Family Configurations
MCF52110 ColdFire Microcontroller, Rev. 1
Freescale Semiconductor
10
1.2.9
QSPI
The queued serial peripheral interface (QSPI) provides a synchronous serial peripheral interface with queued transfer capability.
It allows up to 16 transfers to be queued at once, minimizing the need for CPU intervention between transfers.
1.2.10
Fast ADC
The fast ADC consists of an eight-channel input select multiplexer and two independent sample and hold (S/H) circuits feeding
separate 12-bit ADCs. The two separate converters store their results in accessible buffers for further processing.
The ADC can be configured to perform a single scan and halt, a scan when triggered, or a programmed scan sequence repeatedly
until manually stopped.
The ADC can be configured for sequential or simultaneous conversion. When configured for sequential conversions, up to eight
channels can be sampled and stored in any order specified by the channel list register. Both ADCs may be required during a
scan, depending on the inputs to be sampled.
During a simultaneous conversion, both S/H circuits are used to capture two different channels at the same time. This
configuration requires that a single channel may not be sampled by both S/H circuits simultaneously.
Optional interrupts can be generated at the end of the scan sequence if a channel is out of range (measures below the low
threshold limit or above the high threshold limit set in the limit registers) or at several different zero crossing conditions.
1.2.11
DMA Timers (DTIM0–DTIM3)
There are four independent, DMA transfer capable 32-bit timers (DTIM0, DTIM1, DTIM2, and DTIM3) on the device. Each
module incorporates a 32-bit timer with a separate register set for configuration and control. The timers can be configured to
operate from the system clock or from an external clock source using one of the DTINn signals. If the system clock is selected,
it can be divided by 16 or 1. The input clock is further divided by a user-programmable 8-bit prescaler that clocks the actual
timer counter register (TCRn). Each of these timers can be configured for input capture or reference (output) compare mode.
Timer events may optionally cause interrupt requests or DMA transfers.
1.2.12
General Purpose Timer (GPT)
The general purpose timer (GPT) is a four-channel timer module consisting of a 16-bit programmable counter driven by a
seven-stage programmable prescaler. Each of the four channels can be configured for input capture or output compare.
Additionally, channel three, can be configured as a pulse accumulator.
A timer overflow function allows software to extend the timing capability of the system beyond the 16-bit range of the counter.
The input capture and output compare functions allow simultaneous input waveform measurements and output waveform
generation. The input capture function can capture the time of a selected transition edge. The output compare function can
generate output waveforms and timer software delays. The 16-bit pulse accumulator can operate as a simple event counter or a
gated time accumulator.
1.2.13
Periodic Interrupt Timers (PIT0 and PIT1)
The two periodic interrupt timers (PIT0 and PIT1) are 16-bit timers that provide interrupts at regular intervals with minimal
processor intervention. Each timer can count down from the value written in its PIT modulus register or it can be a free-running
down-counter.
相关PDF资料 |
PDF描述 |
|---|---|
| MCF52110CVM66J | IC MCU 128K FLASH 66MHZ 81MAPBGA |
| MCF52100CVM80J | IC MCU 64K FLASH 80MHZ 81MAPBGA |
| S9S08SG16E1VTG | MCU 16K FLASH 16-TSSOP |
| S9S08AW60E5CPUE | MCU 60KB FLASH AUTO 64-LQFP |
| S9S08AW32E5CFGE | MCU 32K FLASH AUTO 44-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCF5211CAE66 | 功能描述:32位微控制器 - MCU MCF5211 KIRIN RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT |
| MCF5211CEP66 | 功能描述:32位微控制器 - MCU MCF5211 KIRIN RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT |
| MCF5211LCEP66 | 功能描述:32位微控制器 - MCU MCF5211 KIRIN RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT |
| MCF5211LCVM66 | 功能描述:IC MCU 128K FLASH 66MHZ 81MAPBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MCF521x 标准包装:1 系列:87C 核心处理器:MCS 51 芯体尺寸:8-位 速度:16MHz 连通性:SIO 外围设备:- 输入/输出数:32 程序存储器容量:8KB（8K x 8） 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4 V ~ 6 V 数据转换器:- 振荡器型:外部 工作温度:0°C ~ 70°C 封装/外壳:44-DIP 包装:管件 其它名称:864285 |
| MCF5211LCVM80 | 功能描述:IC MCU 128K FLASH 80MHZ 81MAPBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MCF521x 标准包装:1 系列:87C 核心处理器:MCS 51 芯体尺寸:8-位 速度:16MHz 连通性:SIO 外围设备:- 输入/输出数:32 程序存储器容量:8KB（8K x 8） 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4 V ~ 6 V 数据转换器:- 振荡器型:外部 工作温度:0°C ~ 70°C 封装/外壳:44-DIP 包装:管件 其它名称:864285 |
发布紧急采购，3分钟左右您将得到回复。