- 您现在的位置：买卖IC网 > PDF目录15012 > MCP1253-ADJI/MS (Microchip Technology)IC REG MULTI CONFIG ADJ 8MSOP PDF资料下载
参数资料
| 型号： | MCP1253-ADJI/MS |
| 厂商： | Microchip Technology |
| 文件页数： | 10/18页 |
| 文件大小： | 0K |
| 描述： | IC REG MULTI CONFIG ADJ 8MSOP |
| 标准包装： | 100 |
| 类型： | 降压（降压），升压（升压），切换电容（充电泵） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.5 V ~ 5.5 V |
| 输入电压： | 2 V ~ 5.5 V |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 120mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-MSOP |
| 产品目录页面： | 663 (CN2011-ZH PDF) |
MCP1252/3
4.2
Power Efficiency
4.6
Thermal Shutdown
The power efficiency, η , is determined by the mode of
operation. In boost mode, the efficiency is approxi-
mately half of a linear regulator. In buck mode, the effi-
ciency is approximately equal to that of a linear
regulator. The following formulas can be used to
approximate the power efficiency with any significant
amount of output current. At light loads, the quiescent
current of the device must be taken into consideration.
The MCP1252 and MCP1253 feature thermal shut-
down with temperature hysteresis. When the die tem-
perature exceeds 160°C, typically, the device shuts
down. When the die cools by 15°C, typically, the device
automatically turns back on. If high die temperature is
caused by output overload and the load is not removed,
the device will turn on and off, resulting in a pulse out-
put.
EQUATION
5.0
APPLICATIONS
P OUT V O UT × I OU T V OUT
V IN × 2 × I O UT
V IN × 2
η BOOST
= ------------- = ------------------------------------ = ------------------
P IN
The MCP1252 and MCP1253 are inductorless, positive
regulated, charge pump DC/DC converters. A typical
circuit configuration for the fixed output version is
depicted in Figure 5-1. The adjustable version is
P OUT V OU T × I OUT V OU T
η BUCK = = = -------------
------------- --------------------------------
P IN V IN × I OU T V IN
SELECTABLE OUTPUT VOLTAGE
C+
C-
3 V IN
PGOOD
SELECT
7
4.3 Shutdown Mode
Driving SHDN low places the MCP1252 or MCP1253 in
a low power shutdown mode. This disables the charge
pump switches, oscillator and control logic, reducing
the quiescent current to 0.1 μA (typical). The PGOOD
output is in a high-impedance state during shutdown.
4.4 PGOOD Output
The PGOOD output is an open-drain output that sinks
current when the regulator output voltage falls below
C FLY
2.7V to 5.5V
+
C IN
ON
OFF
Shutdown
Control
6
5
MCP1252-33X50
V OUT 2
1
8
SHDN
GND
4
+5.0V ±2.5%
+
R PU C OUT
PGOOD Flag
To PICmicro ?
Microcontroller
C FLY = 1 μF
C IN = 10 μF
C OUT = 10 μF
R PU = 100 k ?
0.93V OUT (typical). The output voltage can either be
fixed when the selectable output device is chosen
(MCP1252-33X50, MCP1253-33X50) or adjustable
from an external resistive divider when the adjustable
device is chosen (MCP1252-ADJ, MCP1253-ADJ). If
FIGURE 5-1: Typical Circuit Configuration
for Fixed Output Device.
ADJUSTABLE OUTPUT VOLTAGE
C+
C-
PGOOD 1
+ C OUT
the regulator output voltage falls below 0.93V OUT (typ-
ical) for less than 200 μsec and then recovers, glitch-
immunity circuits prevent the PGOOD signal from tran-
sitioning low. A 10 k ? to 1 M ? pull-up resistor from
PGOOD to V OUT may be used to provide a logic output.
Connect PGOOD to GND or leave unconnected if not
used.
4.5 Soft-Start and Short-Circuit
Protection
The MCP1252 and MCP1253 features foldback short-
circuit protection. This circuitry provides an internal
soft-start function by limiting in-rush current during
startup and also limits the output current to 200 mA
(typical) if the output is shorted to GND. The internal
soft-start circuitry requires approximately 300 μsec,
C FLY
2.7V to 5.5V
+
C IN
ON
OFF
Shutdown
Control
MCP1252-ADJ
6
V OUT 2
5
3 V IN
7 FB 8
SHDN
GND
4
V OUT = 1.21V (1 + R 1 /R 2 )
+4.0V
R PU
R 1
PGOOD Flag
To PICmicro ?
Microcontroller
R 2
C FLY = 1 μF
C IN = 10 μF
C OUT = 10 μF
R PU = 100 k ?
R 1 = 23.2 k ?
R 2 = 10 k ?
typical with a 5V output, from either initial power-up or
release from shutdown for the output voltage to be in
regulation.
DS21752A-page 10
FIGURE 5-2: Typical Circuit Configuration
for Adjustable Output Device.
? 2002 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6861UK45+T | IC MPU SUPERVISOR SOT23-5 |
| MAX6861UK44+T | IC MPU SUPERVISOR SOT23-5 |
| UVK1V332MHD | CAP ALUM 3300UF 35V 20% RADIAL |
| MAX6862UK20+T | IC MPU SUPERVISOR SOT23-5 |
| MAX6861UK42+T | IC MPU SUPERVISOR SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1253T-33X50I/MS | 功能描述:电荷泵 120mA Regulated RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| MCP1253T-ADJI/MS | 功能描述:电荷泵 120mA Regulated Adj RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 输出电压:- 1.5 V to - 5.5 V, 3 V to 11 V 输出电流:100 mA 电源电流:1 mA 最大工作温度:+ 70 C 封装 / 箱体:SOIC-8 Narrow 封装:Tube |
| MCP1256 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Regulated 3.3V, Low-Ripple Charge Pump with Low- Operating Current SLEEP Mode or BYPASS Mode |
| MCP1256/7/8/9EV | 功能描述:电源管理IC开发工具 MCP1256/7/8/9 Eval Brd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MCP1256_13 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Regulated 3.3V, Low-Ripple Charge Pump with Low- Operating Current SLEEP Mode or BYPASS Mode |
发布紧急采购，3分钟左右您将得到回复。